×
Siemens Industry Online Support
Siemens AG
Entry type: Product note Entry ID: 103624653, Entry date: 02/13/2018
(7)
Rate

Released combinations of AS-i modules in ET 200SP

  • Entry
  • Associated product(s)
List of released configurations for the AS-i modules in the distributed I/O SIMATIC ET 200SP.

For AS-Interface, the following communication modules are available in the distributed  I/O SIMATIC ET 200SP:

CM AS-i Master ST

Article number: 3RK7137-6SA00-0BC1

Further information can be obtained from the delivery release 72865595

F-CM AS-i Safety ST

Article number: 3RK7136-6SC00-0BC1

Further information can be obtained from the delivery release 90880044


The options for using the modules are being optimized in stages. The current status of the configuration options is listed below.

Released configurations for the AS-i modules in the distributed I/O SIMATIC ET 200SP:

Table 1: PROFINET

PROFINET connection for ET 200SP with IM155-6PN HF / IM155-6PN ST / IM155-6PN BA
Note: With IM155-6PN BA, the module F-CM AS-i Safety ST is not applicable
Configuration of SIMATIC station or
SINUMERIK
Released configurations of the AS-i network
Controller Step 7
version
ET 200SP
configuration mode
Suitable
AS-i modules in the ET 200SP
Valid configuration mode
for the AS-i network
CM
AS-i Master ST
F-CM
AS-i Safety
ST
AS-i Basic
Configuration
(without configuration of the AS-i slaves in Step 7)
AS-i Configuration
with
Configuration
of the
AS-i slaves

in Step 7
S7-300 /
S7-400
Step 7 V5.5
(classic)
Hardware catalog
integrated
+ + + +
GSD + - + +
Step 7 V13 SP1
/ Step 7 V14
(TIA Portal)
Hardware catalog
integrated
+ + + +
GSD + - + -
S7-1200 /
S7-1500
Step 7 V13 SP1
/ Step 7 V14
(TIA Portal)
Hardware catalog
integrated
+ + + +
GSD + - + -
SINUMERIK
840D sl
(SW V4.5)
Step 7 V5.5
(classic)
Hardware catalog
integrated
+     + 1) + +
GSD+- + -
For further prerequisites concerning SINUMERIK 109481406

+ : available
- : not available
1) : available as with SINUMERIK SW 4.7 SP2 HF1
 

Table 2: ET 200SP CPU / ET 200SP Open Controller

ET 200SP with ET 200SP CPU / ET 200SP Open Controller
Configuration of ET 200SP Station Released configurations of the AS-i network
Controller Step 7
version
ET 200SP
configuration mode
Suitable
  AS-i modules in the ET 200SP
Valid configuration mode
  for the AS-i network
CM
AS-i Master ST
F-CM
AS-i Safety ST
AS-i Basic
Configuration
(without configuration of the AS-i slaves in Step 7)
AS-i Configuration
with Configuration of the AS-i slaves in Step 7
ET 200SP CPU FW 1.8
S7-1510 (F)
S7-1512 (F)
ET 200 SP
Open Controller
FW 1.8
S7-1515 PC
Step 7 V13 SP1 Update 4
(TIA-Portal)
Hardware-catalog
integrated
+ + + +
  ET 200SP CPU
FW 2.0
S7-1510 (F)
S7-1512 (F)
ET 200SP
Open Controller
FW 2.0
S7-1515 PC (F)
Step 7 V14
(TIA-Portal)
Hardware-catalog
integrated
+ +++
For further prerequisites see text below the table.
+ : available

The module CM AS-i Master ST can be used in an ET 200SP CPU or an ET 200 SP Open Controller station with an ET 200SP CPU instead of an Interface Module (IM). The following minimum requirements for the firmware and software versions apply in this configuration:

  • CM AS-i Master ST with FW V1.1 108742051
  • ET 200SP CPU with FW V1.8 (CPU 1510SP-1 PN, CPU 1510SP F-1 PN, CPU 1512SP-1 PN, CPU 1512SP F-1 PN) 109478459
  • ET 200SP Open Controller with FW V1.8 (Open Controller CPU 1515SP PC) 109478528
  • Configuration with STEP 7 V13 SP1 Update 4 109311724

alternatively

The module F-CM AS-i Safety ST in an ET 200SP station with an ET 200SP CPU instead of an Interface Module (IM) needs to be configured with the new version V3.0 of the HSP 0070, i.e. the following minimum requirements for the firmware and software versions apply in addition to the above mentioned items:

  • Configuration with STEP 7 Safety V13 SP1 Update 4 109477092
  • In addition: New version HSP 0070 V3.0 is required 72341852

alternatively

  • Configuration with STEP 7 V14 (HSP 0070 V3.0 is included) 109739471

 

Table 3: PROFIBUS

PROFIBUS connection for ET 200SP with IM155-6DP HF
Configuration of SIMATIC station or
SINUMERIK
Released configurations of the AS-i network
Controller Step 7
version
ET 200SP
configuration
mode
Suitable
AS-i modules in the ET 200SP
Valid configuration mode
for the AS-i network
CM
AS-i Master ST
F-CM
AS-i Safety
ST
AS-i Basic
configuration
(without
configuration
of the
AS-i slaves
in Step 7)
AS-i
configuration
with
Configuration
of the
AS-i slaves

in Step 7
S7-300 /
S7-400
Step 7 V5.5
(classic)
Hardware catalog
integrated
+ + + +
GSD + - + -
Step 7 V13 SP1
(TIA Portal)
Hardware-catalog
integrated
+ + + +
GSD + - + -
S7-1200 /
S7-1500
Step 7 V13 SP1
(TIA Portal)
Hardware-catalog
integrated
+ + + +
GSD + - + -
SINUMERIK
840D sl
(SW V4.5)
Step 7 V5.5
(classic)
Hardware-catalog
integrated
+    + 1)++
GSD + - + -
For further prerequisites concerning SINUMERIK 109481406

+ : available
- : not available
1) : available as with SINUMERIK SW 4.7 SP2 HF1

 

Additional Information:

  1. General notes:
    In addition to the above, combinations may also be possible with lower versions than those specified.

    In the case of an AS-i basic configuration (without configuration of the AS-i slaves in Step 7) the configuring of the AS-i slaves is performed by using the appropriate function "Apply slave configuration (ACTUAL ->CONF)" or by using the optional SET pushbutton.

  2. Safety applications:
    The relevant F-CPU and the current Distributed Safety or Safety Advanced or F Systems option package are required to operate the F-CM AS-i Safety ST failsafe module.
    Certificate 90477145

    Please observe the information about released modules, in particular F-CPU hardware and firmware, and related software given in the following entries:

     

    SIMATIC S7 F/FH Systems certificate Z10 16 06 20080 004 109482447

    SIMATIC S7 Distributed Safety certificate Z10 17 05 67803 015  47920156

    SIMATIC Safety Systems certificate Z10 16 02 67803 010  57141289

    F-Configuration Pack 15208817


    Correction of the manual "F-CM AS-i Safety ST" Edition 03/2017, Ch. 5.1 "Configuring the F-CM AS-i Safety ST":
    The note "Operation under S7 F systems is not approved." is canceled.
    The table item "Configuration software" is to be extended: "STEP 7 (classic) V5.5 SP4 or higher with Distributed Safety or F Systems"
    The correction will be adopted in the next edition of the manual.

  3. Shared Device:
    The Shared Device option (for PROFINET) is approved for use with the CM AS-i Master ST (FW V1.1 or higher) and F-CM AS-i Safety ST modules with STEP 7 V14 (or higher). For more information, see "SIMATIC ET 200SP Distributed I/O system" System Manual 58649293

  4. Hardware Support Package:
    The availability of the modules in Step 7 may require an update of the hardware catalog (Hardware Support Package, HSP).

     

    Procedure in Step 7 V5.5 (classic) / HW config: Options -> Install HW Updates 23183356

    Procedure in Step 7 V13 SP1 (TIA Portal): Options -> Support packages 72341852

  5. GSD files:
    An F-CM AS-i Safety ST failsafe module cannot be configured using a GSD file as the GSD specification does not provide a safety-related setting of module-specific parameters.

    Download the PROFINET GSD ET 200SP 57138621

    Download the PROFIBUS GSD ET 200SP 73016883

  6. Diagnosis:


    For the CM AS-i Master ST and  F-CM AS-i Master ST modules, an optional diagnostic block package with visualization via HMI panel or web browser is available to be integrated into the user program.
    For further information and conditions of use 109479103

Security information
In order to protect technical infrastructures, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art IT security concept. Siemens’ products and solutions constitute one element of such a concept. For more information about cyber security, please visit
https://www.siemens.com/cybersecurity#Ouraspiration.
Support to the statistics
With this function the IDs found are listed according to number (format .txt).

Generate list
Copy URL
Display page in new design
mySupport Cockpit
Related links