Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

SOFT STARTER 3RW44 PROBLEM

Created by: Kadhar at: 1/10/2012 6:04 AM (4 Replies)

Rating (0)

Thanks 0

5 Entries

1/10/2012 6:04 AM	Rate (0)
Kadhar Posts: 16 Rating: (0)	Hello, We are using 3RW44 Soft Starter for one of our application long travel movement.we connected 8 number of motors with capacity 3.7kw. please find below the setting on the soft starter. Rated Operating Current le=62A Rated Operating torque= 171Nm Rated Operating speed=945 Starting mode= voltage ramp start voltage=50% starting time=5 sec Breakway voltage=40% stopping mode=torque control stopping time=3 sec stopping torque=40% minimum current limit=19% maximum current limit=113% Input1 Action= motor Right PS1 Input4 Action=Trip Reset Output1 Action=On time motor Output2 Action=Operation/Bypass After Start command is given from joystick, first we are energizing main contactor so that soft starter will receive 415V supply and it will work and after 4sec it will get bypassed by bypass contactor. we found soft starter got tripped by the fault "PHASE ANGLE CONTROL FAILURE" and at that time we noticed that blue phase to phase voltage becomes 0 value. So kindly request you to suggest on this issue.
Kadhar Posts: 16 Rating: (0)
Suggestion To thank Quote Answer

1/10/2012 10:10 AM	Rate (0)
Marcjan Platinum Member Joined: 4/22/2010 Last visit: 11/18/2024 Posts: 5697 Rating: (715)	Hello, I think there are some usefull tips in the [url=http://support.automation.siemens.com/WW/view/en/21772518] Manual [/url] Chapter 7 Regards, Marcjan
	Last edited by: Marcjan at: 1/10/2012 10:18 AM Attachment didn''''t work, link added Last edited by: Marcjan at: 1/10/2012 10:10 AM Problem solved? Please let us know! Please no technical questions by PM, use the forum sections for your questions.
Suggestion To thank Quote Answer

9/26/2018 8:42 AM	Rate (0)
sree27 Posts: 1 Rating: (0)	Hellow we facing a problem in 3RW44 STARTING IT GETS TRIP. Fault message is Phase angle control failure. it is a compressor nominal current-295A Starting U+CURRENTLIMIT Starting voltage 50% current limit 400% please reply on this issue.
sree27 Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

2/23/2020 8:39 AM	Rate (0)
Madadi Bronze Member Joined: 12/28/2016 Last visit: 11/4/2024 Posts: 435 Rating: (51)	sree27 Hellow we facing a problem in 3RW44 STARTING IT GETS TRIP. Fault message is Phase angle control failure. it is a compressor nominal current-295A Starting U+CURRENTLIMIT Starting voltage 50% current limit 400% please reply on this issue. Check the following. 1. Error occurs without motor starting. Cause: - Motor has not been connected correctly. - Inside delta circuit incorrectly configured. - Ground fault present. Remedy: Check and rectify wiring (see inside delta circuit wiring suggestions). 2. Error occurs during starting. Cause: - Start voltage too high - Breakaway pulse set (incorrectly): instable motor start (Only set breakaway pulse if absolutely necessary. In the case of pumps, for example ,a breakaway pulse can often cause misfiring.) If there is an idle time of < 5 s since the last start, the 3RW44 starts with a higher start voltage. In combination with a set breakaway pulse, this can lead to "Incorrect start conditions". Remedy: Adjust parameters or increase idle time
	https://pnap.ir If this Information really helps, you could use the Rate function😉
Suggestion To thank Quote Answer

8/22/2022 12:48 PM	Rate (0)
Jen_Moderator Diamond Member Joined: 6/19/2017 Last visit: 9/6/2024 Posts: 8175 Rating: (172)	New question published by Mah66 is split to a separate thread with the subject 3RW44: How can set up rotation direction by adjusting input IN1?. Best regards Jen_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on