SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

USS Protocol with td 200 op.

Created by: chechevali at: 3/3/2009 8:56 AM (6 Replies)

Rating (0)

Thanks 0

7 Entries

3/3/2009 8:56 AM	Rate (0)
chechevali Posts: 15 Rating: (0)	Dear all, I am using cpu 226 and td 200 to communicate a micromaster drive with USS protocol. When i write a simple program and data block for td 200 panel ( by td 200 wizard) i get message from td 200 that "NO PARAMETER BLOCK". When i erase uss commands and loading same program i can see messages at TD 200. I am using only port 1 cause i know port0 reserved for USS protocol. Whan can be causal reasons. Regards,
chechevali Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/4/2009 7:16 AM	Rate (0)
Ayubo Posts: 18 Rating: (0)	Hello Chechevali, Check followings in the TD configuration. 1. Address Parameter Block.- should match with memory allocation of TD wizad 2. Baud Rate - should match with your Port 1 baud rate 3. TD 200 Address - shouldmatch As per your problem, it seems the issue is the value in the Address Parameter Block of the TD. Go to the TD Wizad again. In the first introduction window it shows the address(TD 200 configuration (VW*). . Use the same value(*) in the add Parameter Block in the TD. It should work then.
Ayubo Posts: 18 Rating: (0)
Suggestion To thank Quote Answer

3/6/2009 10:15 AM	Rate (0)
chechevali Posts: 15 Rating: (0)	Dear Ayubo, i did all what you wrote, it is still same. i am sending the projectmaybe you can find where is the mistake. network 1 LD I0.1 S M0.1, 1 network 2 LD I0.2 R M0.1, 1 network 3 LD SM0.0 CALL USS_INIT, 1, 9600, 1, M0.0, VB10 network 4 LD SM0.0 = L60.0 LD M0.1 = L63.7 LDN M0.1 = L63.6 LD I0.2 = L63.5 LD I0.3 = L63.4 LD I0.4 = L63.3 LD L60.0 CALL USS_CTRL, L63.7, L63.6, L63.5, L63.4, L63.3, 1, 1, VD32, M0.1, VB15, VW17, VD19, Q0.0, Q0.1, Q0.2, Q0.3 network 5 LD SM0.0 = V200.7 DATA BLOCK TD_DATA_0 VB100 'TD' // VB102 16#10 //Set Language to English, set Update to as fast as possible VB103 16#80 //Set the display to 20 character mode; Enter key V103.1; Up key V103.2; Down key V103.3; VB104 1 //Set the number of messages VB105 16#01 //Set the Function Keys notification bits to M1.0 - M1.7, F-Keys configured to set M-bits VW106 150 //Set the starting address for messages to VB150 VW108 200 //Set the starting address for message enable bits to VB200 VW110 65535 //Global Password (if enabled) VW112 2 //Character Set = Latin 1 (Bold) //MESSAGE 1 //Message Enable Bit V200.7 VB150 'MOTOR % ' // VB158 16#10 //Edit Notification V158.2; No Acknowledgement;No Password; VB159 16#20 //Signed Double Word; 0 Digits to the right of the decimal; VD160 16#00000000 //Embedded Data Value: Move data for display here. VB164 ' ' // //END TD200_BLOCK ------------------------------ // //DATA PAGE COMMENTS // //Press F1 for help and example data page //
chechevali Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/8/2009 7:56 AM	Rate (0)
Ayubo Posts: 18 Rating: (0)	Dear chechevali, Can you please attached the program as an attachment.
Ayubo Posts: 18 Rating: (0)
Suggestion To thank Quote Answer

3/8/2009 12:12 PM	Rate (0)
chechevali Posts: 15 Rating: (0)	Dear Ayubo, Just .zip .gif .jpeg .pdf files can be attached.Could youpaste and copy the text that i wrote?
chechevali Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/8/2009 1:54 PM	Rate (0)
Ayubo Posts: 18 Rating: (0)	Hi I found I bug in Network 3: ForUSS_INIT use SM0.1 instead of SM0.0. Asiri
Ayubo Posts: 18 Rating: (0)
Suggestion To thank Quote Answer

3/9/2009 7:12 AM	Rate (0)
chechevali Posts: 15 Rating: (0)	It works Thank you Ayubo for your all support
chechevali Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...

SiePortal

Created by: chechevali at: 3/3/2009 8:56 AM (6 Replies)

Rating (0) Thanks 0

7 Entries

7 Entries

Follow us on

Rating (0)

Thanks 0