SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Problem in Seting PG/PC Interface" Step 7 Microwin "

10/12/2009 5:28 PM	Rate (0)
Walid Elshazly Posts: 100 Rating: (0)	Hi , I have Aproblem inSettingPG/PC interface with my new windows in The MicrowinSoftware , when I select PC adapter (PPI) and press Ok on the communication wizard the following message in theattachedPictureappears the Error message is : port cannot be opened or isbeingused by another application What is the Error that I did.........???? Attachment Communication Wizard.JPG (460 Downloads)
Walid Elshazly Posts: 100 Rating: (0)
Suggestion To thank Quote Answer

10/13/2009 2:52 AM	Rate (0)
AisMan Posts: 2 Rating: (0)	your local PC node address is 0, can you try to change to 1 and give it a try again?
AisMan Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

10/13/2009 10:24 AM	Rate (0)
Walid Elshazly Posts: 100 Rating: (0)	Hello Aisman , I have been tried to do that many Times But the problem didn't been solved ,
Walid Elshazly Posts: 100 Rating: (0)
Suggestion To thank Quote Answer

10/13/2009 12:48 PM	Rate (0)
Robster Platinum Member Joined: 5/28/2008 Last visit: 11/11/2025 Posts: 1344 Rating: (141)	This message means the com-port of your PC is in use. Have you opened two MicroWin Windows? Also check if you have run any other applications that is using com-port.

Suggestion To thank Quote Answer

10/13/2009 1:58 PM	Rate (0)
Husam Posts: 101 Rating: (14)	Close any programs running in the background on the taskbar ... etc, even close Mircowin, and try again with a new instance of the Microwin ... Let me know if that helps. worst comes to worst, reboot your PC then try again. Thank you,
Husam Posts: 101 Rating: (14)
Suggestion To thank Quote Answer

10/13/2009 4:44 PM	Rate (0)
Walid Elshazly Posts: 100 Rating: (0)	Hi Robster , I Us an USB adapter and select the communication port in local connection is USB , and the problemdidn'tsolved , Dear Husam , Your Suggestions was the first way I have been gone , But No Change ,
Walid Elshazly Posts: 100 Rating: (0)	Last edited by: Walid Elshazly at: 10/13/2009 4:45 PM
Suggestion To thank Quote Answer

10/13/2009 4:52 PM	Rate (0)
Robster Platinum Member Joined: 5/28/2008 Last visit: 11/11/2025 Posts: 1344 Rating: (141)	ok, PC/PPI cable USB. Settings are 19k2 Baud, no multimaster and no advanced PPI ? Is the driver installed correctly? Have you disconnect/connect cable from USB port to re-initalize? What version of Micro/Win you have and what version of PLC?

Suggestion To thank Quote Answer

10/13/2009 6:20 PM	Rate (0)
Impechileh Posts: 3 Rating: (0)	Hi, In the properties of the PC adapter(PPI), Increase the transmission rate to the maximum and read the plc by double clicking the refresh button on the communications. thnx
Impechileh Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

10/13/2009 7:16 PM	Rate (0)
Niranjan Prasad Posts: 691 Rating: (37)	Try With PC Adapter( Auto) Go for Start Network Detection in the Properties Tab Try in putting the CPU in STOP mode
Niranjan Prasad Posts: 691 Rating: (37)	Last edited by: Chimpu at: 10/13/2009 8:00 PM
Suggestion To thank Quote Answer

Share this page:

Share this page on...