Navigation

Unable to run drive with OP1S

Created by: The dog at: 11/25/2011 5:03 PM (6 Replies)

Rating (0)

Thanks 1

7 Entries

11/25/2011 5:03 PM	Rate (0)
The dog Posts: 7 Rating: (0)	I am not able to start my drive ( 6SE7012-OTP60-Z )via the OP1S. The drive is configured, and I am able to run my motor with the "master control" in DriveMonitor. I have also tried to start the motorwith a DI signal on theX101-terminals, this works without problems. ..but..when I try to use the OP1S, I just get a message: "ON-COMMAND NOT AVAILABLE" The OP1S finds and connects to the slave. It shows the status as it should, and also shows the speed and everything when I run the motor from DriveMonitor. I am able to change parameters via the panel..so the connection should be fine. P701 Serial interface is set to9600 baud. I have set most of the control-word bits to 1, and connected 554.1 to B2100. The drive status is 'Rdy On'. All OFF-signals, Pulse Enable, etc etc are glowing with a beautiful green colour in that DriveMonitor control-panel thing. All bits in P053 are set to 1... So, why am I not able to start the drive with the on-button on OP1S?
The dog Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

11/28/2011 9:48 AM	Rate (0)
The dog Posts: 7 Rating: (0)	hmm..noone got any idea? :-/
The dog Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

11/28/2011 11:36 PM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 11/25/2025 Posts: 1521 Rating: (327)	Hiya, as you are using a Compact Plus, try setting P554.1 to B6100. Regards, Graeme

Suggestion To thank Quote Answer

11/29/2011 9:29 AM	Rate (0)
The dog Posts: 7 Rating: (0)	Ah, that did the trick. Thanks
The dog Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

12/2/2011 7:08 AM	Rate (0)
KimBH Regular Member Joined: 12/1/2011 Last visit: 1/12/2026 Posts: 16 Rating: (0)	Try setting P590=1, P554.002=B2100. hope the drive starting from OP1S.

Suggestion To thank Quote Answer

12/2/2011 7:42 PM	Rate (0)
Graeme Platinum Expert Joined: 6/4/2008 Last visit: 11/25/2025 Posts: 1521 Rating: (327)	KimBH Try setting P590=1, P554.002=B2100. hope the drive starting from OP1S. Hello KimBH, Please check your function diagrams, "The dog's" drive is a compact PLUS (6SE7012-OTP60) Function Diagram 60 shows the binnectors to use for a compact/chassis unit (From B2100) Function Diagram 61 shows the binnectors to use for a Compact PLUS unit (From B6100) Regards, Graeme

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Vithani

12/6/2011 9:52 AM

Rate (0)

KimBH

Regular Member

Joined: 12/1/2011

Last visit: 1/12/2026

Posts: 16

Rating:

(0)

Graeme
KimBH

Try setting P590=1, P554.002=B2100.

hope the drive starting from OP1S.

Hello KimBH,
Please check your function diagrams, "The dog's" drive is a compact PLUS (6SE7012-OTP60)
Function Diagram 60 shows the binnectors to use for a compact/chassis unit (From B2100)
Function Diagram 61 shows the binnectors to use for a Compact PLUS unit (From B6100)
Regards,
Graeme

SiePortal

Unable to run drive with OP1S

Created by: The dog at: 11/25/2011 5:03 PM (6 Replies)

Rating (0)

Thanks 1

7 Entries

The dog

The dog

Graeme

The dog

KimBH

Graeme

This contribution was helpful to

KimBH

7 Entries

Follow us on

SiePortal

Created by: The dog at: 11/25/2011 5:03 PM (6 Replies)

Rating (0) Thanks 1

7 Entries

This contribution was helpful to

7 Entries

Follow us on

Rating (0)

Thanks 1