Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Measuring_Input

Created by: TechWing at: 8/26/2016 9:37 AM (9 Replies)

Rating (0)

Thanks 0

10 Entries

8/26/2016 9:37 AM	Rate (0)
TechWing Posts: 305 Rating: (2)	Measuring_Input set off ,how can clean the Measuring_Input value ? look at the picture ,i has one button,cyclic press and release ,but the count not the same ,why ? Attachment 111.png (265 Downloads)
TechWing Posts: 305 Rating: (2)	Last edited by: TechWing at: 8/26/2016 9:47:25 AM
Suggestion To thank Quote Answer

8/26/2016 9:42 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/21/2026 Posts: 22829 Rating: (3074)	which value exactly? Please write the corret and complete systemvariable which you will reset!

Suggestion To thank Quote Answer

8/26/2016 9:49 AM	Rate (0)
TechWing Posts: 305 Rating: (2)	i want to reset Measuring_Input expert data ,about "counterMeasuredValue1/2、measuredValue1"
TechWing Posts: 305 Rating: (2)
Suggestion To thank Quote Answer

8/26/2016 9:50 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/21/2026 Posts: 22829 Rating: (3074)	Hello, the values must not be the same! This depends of the Command parameters you use and the incomming Singnals on the Measuring Input. You can try to clean the values with the _reset command on the measuringInput. Regards Christoph

Suggestion To thank Quote Answer

8/26/2016 10:00 AM	Rate (0)
TechWing Posts: 305 Rating: (2)	tks,the value is can reset. but ,"the values must not be the same!",i use one button to test it ,up / down count ,why not the same ? "counterMeasuredValue1" is up button count ; "counterMeasuredValue2" is down button count ? the cycle time ? Attachment 111.jpg (282 Downloads)
TechWing Posts: 305 Rating: (2)	Last edited by: TechWing at: 8/26/2016 10:01:33 AM Last edited by: TechWing at: 8/26/2016 10:03:34 AM
Suggestion To thank Quote Answer

8/26/2016 10:04 AM	Rate (0)
jacek d Platinum Member Joined: 9/23/2005 Last visit: 1/20/2026 Posts: 5155 Rating: (772)	Do both counter values always increase by 1 after button press/release ? Contact bouncing could be the reason.
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

8/26/2016 10:11 AM	Rate (0)
TechWing Posts: 305 Rating: (2)	ok,next time,i will be change ather test it .
TechWing Posts: 305 Rating: (2)	Last edited by: TechWing at: 8/26/2016 10:11:46 AM
Suggestion To thank Quote Answer

8/26/2016 11:13 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 1/21/2026 Posts: 22829 Rating: (3074)	Hi, other thing is the mode you use : Both Edges, rising first or falling first .... This can also influence this counter Values. Regards Christoph

Suggestion To thank Quote Answer

8/26/2016 12:06 PM	Rate (0)
TechWing Posts: 305 Rating: (2)	OK
TechWing Posts: 305 Rating: (2)
Suggestion To thank Quote Answer

8/26/2016 10:50 PM	Rate (0)
Marko Bursic Posts: 1410 Rating: (154)	If there are more transitions within one IPO cycle, the Mearing Input object won't return the exact number of transitions, which makes sense.
Marko Bursic Posts: 1410 Rating: (154)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on