SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

p0700 is missing

Created by: Anit Kumar at: 7/6/2012 12:22 PM (7 Replies)

Rating (0)

Thanks 1

8 Entries

7/6/2012 12:22 PM	Rate (0)
Anit Kumar Posts: 153 Rating: (2)	parameter P0700 is not coming in parameter list with BOP-2. I have set P0003 as 3 even then it is not coming. Pls tell me how can I access P0700 for command soucre selection??? I am using Control Unit CU 240E-2 (6SL3244-0BB12-1BA1) ver.A04-4.5 with Sinamics G120.
Anit Kumar Posts: 153 Rating: (2)
Suggestion To thank Quote Answer

7/10/2012 10:39 AM	Rate (0)
Ashutosh Kr Bronze Member Joined: 3/15/2011 Last visit: 4/23/2025 Posts: 134 Rating: (9)	First check P15, it should be 12 . if this does't help Factory reset your drive.i have the configured the above contol unit in starter ,i can see parameter 700.Try going online via Starter.

Suggestion To thank Quote Answer

7/12/2012 9:00 AM	Rate (0)
Anit Kumar Posts: 153 Rating: (2)	thaks Ashutosh Kr for reply!!! My problem is solved and my system is running, actually in CU 240E-2 V 4.5 parameter p0700 is not coming.you also can try using starter v4.3 and supported SSP.
Anit Kumar Posts: 153 Rating: (2)	Last edited by: Anit at: 7/12/2012 9:01 AM
Suggestion To thank Quote Answer

12/8/2013 7:18 AM	Rate (0)
Arunram V Experienced Member Joined: 1/23/2012 Last visit: 11/6/2025 Posts: 33 Rating: (0)	Mr. Anit Kumar , Pls tell how did solved the issue i have the same problem . i cant able to see the P700 using BOP . My inverter Model is G120C DP . then i dont use starter software i have to do commissioning with BOP . Regards Arunram Vasudevan

Suggestion To thank Quote Answer

12/10/2013 3:14 AM	Rate (0)
Joselo Posts: 1 Rating: (0)	Hello, I have the same problem, whould you be kind to tell me what did you do? I can't find P0700 :/ Regards...
Joselo Posts: 1 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users wifoz

1/6/2014 8:39 AM	Rate (0)
Anit Kumar Posts: 153 Rating: (2)	In these Control Units command source is defined by macro (p0015), So check your manual and run appropriate macro . one more solution is : start cmd from DI0............put P840=r722.0 and like wise you can do ....
Anit Kumar Posts: 153 Rating: (2)
Suggestion To thank Quote Answer

3/13/2015 7:54 PM	Rate (0)
wifoz Advanced Member Joined: 9/23/2014 Last visit: 7/29/2025 Posts: 24 Rating: (1)	Joselo Hello, I have the same problem, whould you be kind to tell me what did you do? I can't find P0700 :/ Regards... You should use macros, P15

Suggestion To thank Quote Answer

1/29/2017 8:32 AM	Rate (0)
plc_control321 Posts: 2 Rating: (0)	dear friend go to the paramatre p15 and chose 12 for start and stop from start cmd from DI0 and then put P840=r722.0 and you can turn the motor now best regards
plc_control321 Posts: 2 Rating: (0)	Last edited by: plc_control321 at: 1/29/2017 8:33:24 AM
Suggestion To thank Quote Answer

Share this page:

Share this page on...

SiePortal

p0700 is missing

Created by: Anit Kumar at: 7/6/2012 12:22 PM (7 Replies)

Rating (0)

Thanks 1

8 Entries

Anit Kumar

Ashutosh Kr

Anit Kumar

Last edited by: Anit at: 7/12/2012 9:01 AM

Arunram V

Joselo

This contribution was helpful to

Anit Kumar

wifoz

plc_control321

Last edited by: plc_control321 at: 1/29/2017 8:33:24 AM

8 Entries

Related topics by keywords:

Follow us on

SiePortal

Created by: Anit Kumar at: 7/6/2012 12:22 PM (7 Replies)

Rating (0) Thanks 1

8 Entries

Last edited by: Anit at: 7/12/2012 9:01 AM

This contribution was helpful to

Last edited by: plc_control321 at: 1/29/2017 8:33:24 AM

8 Entries

Related topics by keywords:

Follow us on

Rating (0)

Thanks 1