Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

840 D Power line /PLC S7-300 Profibus Connector

Created by: Rana Ali at: 1/26/2020 5:32 PM (5 Replies)

Rating (1)

Thanks 5

6 Entries

1/26/2020 5:32 PM	Rate (0)
Rana Ali Posts: 110 Rating: (3)	Hi every one 1. How we check the 9 pins DB Profibus RS485 connector which has two wire Used for communication NCU to PCU and PLC S7-300 How we test or check the cable and connector that its working fine ( resistance, Voltage, continuity ) ? 2. Switches Position is on or Off of connectors ,i means Which is the postion is correct ( On or off) Rana Ali Attachment Profibus Rs485.png (128 Downloads)
Rana Ali Posts: 110 Rating: (3)	Last edited by: Rana Ali at: 01/27/2020 16:54:32 Last edited by: Rana Ali at: 01/27/2020 17:21:11 Last edited by: Rana Ali at: 01/27/2020 17:23:10 Last edited by: Rana Ali at: 01/27/2020 20:03:58
Suggestion To thank Quote Answer

1/28/2020 3:31 AM	Rate (0)
Rana Ali Posts: 110 Rating: (3)	Hi Experts Can any one tell me about Profibus Connector checking Procedure Rana Ali Attachment Profibus Rs485.png (103 Downloads)
Rana Ali Posts: 110 Rating: (3)
Suggestion To thank Quote Answer

1/28/2020 4:51 AM	Rate (1)
PISCEAN 2010 Posts: 8092 Rating: (884)	Please refer attached sheet. Profibus connection first & last terminal resistor of the netwrok muct be ON & others in between must be OFF. HTH Attachment Profibus connector checking.pdf (174 Downloads)
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users Rana Ali nulizhang asimpage

1/30/2020 12:53 AM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 1/19/2026 Posts: 4579 Rating: (416)	Hi, Friend, PISCEAN 2010 GAVE you a good way to check that connector maybe cable as well. From me, I have my own test bench , I will set up PRUFIBUS communication from 840D PL to ext. PB Slave , to see the communication is good or not, --and I help customer in the real cases for troubleshooting by this way Siemens (and other companies ) made special devices to scan PB network and connectors, to find bad notes (connectors) or lower signals
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Rana Ali

1/30/2020 3:17 AM	Rate (0)
Rana Ali Posts: 110 Rating: (3)	Hi Sir Nulizhang Thanks for your alway good response sir i want to prepared this test bench setup so how i can prepared this. which type of hardware and software required or material required Rana Ali
Rana Ali Posts: 110 Rating: (3)
Suggestion To thank Quote Answer

1/31/2020 12:54 AM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 1/19/2026 Posts: 4579 Rating: (416)	You need PG or PC installed Siemens SIMATIC MANAGER (STEP7 program sw) I forget which country are you living and working easy to get from Siemens?
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Rana Ali

|

Share this page:

Share this page on...

Follow us on