Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Hardware component not available due to type mismatch

Created by: El Turc at: 4/18/2016 10:48 AM (15 Replies)

Rating (0)

Thanks 6

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

4/18/2016 12:00 PM	Rate (0)
jacek d Platinum Expert Joined: 9/23/2005 Last visit: 9/18/2025 Posts: 5119 Rating: (768)	Also check: 1 - cabling; 2 - IP address of the Cognex device - ping it; 3 - Profinet device name of the Cognex device - Primary Setup Tool or software form Cognex.
	Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

4/18/2016 12:02 PM	Rate (0)
El Turc Posts: 17 Rating: (0)	Hi Yes i use the correct file :/ Kahl Hi! Do you use the correct GSDML file for that camera?
El Turc Posts: 17 Rating: (0)
Suggestion To thank Quote Answer

4/18/2016 12:06 PM	Rate (0)
El Turc Posts: 17 Rating: (0)	Hi the profinet device name of the Cognex is in-sight and it's different of the name of PLC jacek d Also check: 1 - cabling; 2 - IP address of the Cognex device - ping it; 3 - Profinet device name of the Cognex device - Primary Setup Tool or software form Cognex.
El Turc Posts: 17 Rating: (0)
Suggestion To thank Quote Answer

4/18/2016 12:07 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/18/2025 Posts: 22710 Rating: (3071)	Hi, and is the name in-sight which offline cionfigured active on the device online, have you check that? Regards Christoph

Suggestion To thank Quote Answer

4/18/2016 8:11 PM	Rate (0)
El Turc Posts: 17 Rating: (0)	Thanks everyone i found the problem it was a name problem
El Turc Posts: 17 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 4 thankful Users Kahl jacek d zzVss 0_Einstein

4/19/2016 5:29 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 9/18/2025 Posts: 16121 Rating: (2515)	Profinet is very demanding. It requires the name and ip address to be exactly the same in the PLC and in the device. Profibus just needs the address to be correct. El Turc Thanks everyone i found the problem it was a name problem
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users grrrrrroooo El Turc

|

Share this page:

Share this page on...

Follow us on