Dear Experts,

                      Am uSing S7-1200 PLc Order Number : 6ES7 214-1AE30-0xb0. 

                      Previously Some Other programmer perfectlydone the program , Aft That Machine is running well. Now Customer Want to Modify Program . 

                      So I have Visited And Am trying to Upload the Program Backup . But I cant . Am using Software TIA version 13. .

                       Please Help this . Herewith I have Attached the Image . Plz find it .

Regards,

Arasan..

Arasan

Dear Experts,

                      Am uSing S7-1200 PLc Order Number : 6ES7 214-1AE30-0xb0. 

                      Previously Some Other programmer perfectlydone the program , Aft That Machine is running well. Now Customer Want to Modify Program . 

                      So I have Visited And Am trying to Upload the Program Backup . But I cant . Am using Software TIA version 13. .

                       Please Help this . Herewith I have Attached the Image . Plz find it .

Regards,

Arasan..

 Hello,

It depends on the version of TIA with which the program was downloaded. Do you know the version of TIA that the previois Programmer was using?

Hello Ibrahim Fathy,

                                I dnt Know.. Previous programmer Using Software name Or Version of Software . I Dnt know . Last backup also They Dnt have .. I Dnt Know .. what shall we do that .

Thank you .

Regards,

Arasan..

Hello 

Did you inform us about the TIA portal Version which you are using ?

Two solutions : 

1) you install the correct tia version because yours is different.

2) you try installing this : https://support.industry.siemens.com/cs/document/82169157/in-step-7-(tia-portal)-v13-sp1-how-do-you-load-project-data-from-a-device-that-has-been-configured-with-step-7-(tia-portal)-v12-or-v13?dti=0&lc=en-WW

Hello Arasan,

your situation can be not bad, because you can download all needed TIA versions and use it as trial licence with full functionality. Due CPU type I'll be start with TIA v11, try upload with this version for first. I don't know if TIA v10.5 is still accessible for download, test. After that you can install TIA v12 and test it also. Don't forget install also needed HSP packs for that versions. Give us info about conclusion.

Hello,

          I have try to go Online In Tia V13 Software . I will Go for Accessible Node . In that Plc Showing In Online In Corresponding  IP address . Aft That I try to Upload from device . There is a problem . Connection PLC does not Assign IP ..?? This Message is showing while Am Upload the Program Backup ..

       And I ill go to Diagonisitc Buffer And I try to assign The IP , But its not assingning .. What Shall we do ..??/

Regards,

Arasan..

Arasan

Dear Experts,

                      Am uSing S7-1200 PLc Order Number : 6ES7 214-1AE30-0xb0. 

                      Previously Some Other programmer perfectlydone the program , Aft That Machine is running well. Now Customer Want to Modify Program . 

                      So I have Visited And Am trying to Upload the Program Backup . But I cant . Am using Software TIA version 13. .

                       Please Help this . Herewith I have Attached the Image . Plz find it .

Regards,

Arasan..

 Dear Arasan

If you do not know the TIA version then it will create a problem for taking upload and you have to try it with both V11 and V12 

Yet I think

S7-1200 have many issue whenever there is a TIA ver change .

The main important part is its firmware version.

If in 1200 FW>=4.0 you will be able to upload both HW/SW but if less then it then you will have to create the H/W as present and feed all the required parameter then you can only take the block upload

this is the case if from V11 or V12 to V13 and is also possible if and only if you download the upgraged original V13 backupp to CPU

Dear Smit Shah,

                         Ya . i can understand In S7-1200 PLC , FW version issue. But my problem is i ill going for online . Only thing is diagonistic buffer itself Ur plc does not assign plc Message is appear ..??

                        But i tryed to assign PLC ip . But is not taken .. I have shared image For assign the IP . But i is not assign here.???

                               Plz Help this support ..