Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

IM 153-2 module not reachable

Created by: Ahmed_Atef. at: 7/15/2020 9:14 AM (8 Replies)

Rating (0)

Thanks 1

9 Entries

7/15/2020 9:14 AM	Rate (0)
Ahmed_Atef. Advanced Member Joined: 7/23/2016 Last visit: 4/29/2024 Posts: 37 Rating: (0)	Hello every body Could any engineer help me in this problem , the IM 153-2 module is not reachable in my project , i using CPU 315-2 with that module , i changed the bus cable and connectors and changed the IM 153-2 module , but the same problem Attachment 3.JPG (661 Downloads)
	Last edited by: Ahmed_Atef. at: 07/15/2020 09:19:52 Ahmed Atef
Suggestion To thank Quote Answer

7/15/2020 10:37 AM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	Hello, sry, very few infos about your problem. 1. exact order number of ET200M module / firmware. There are more versions with diifferent capabilities so pls understand that your info is not ok. 2. DP addresses set on devices, in case ET200M module has dip switches, you need set correctly as prj is set. 3. set operation mode on Master CPU. 4. exact cable wiring, for sure. 5. generally, it's expected as final rebuild HW option with also rebuild SW completelly prior download all inside PLC. 6. last recommendation is check diag buffer inside PLC, you can save it also as txt file (option is there) and add this txt file to ZIP. ZIP screenshots and attach ZIP file here.
	Last edited by: Duris_I at: 07/15/2020 10:38:41 With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users TJ Matthew

7/15/2020 12:05 PM	Rate (0)
Ahmed_Atef. Advanced Member Joined: 7/23/2016 Last visit: 4/29/2024 Posts: 37 Rating: (0)	dear sir 1- the old ET200M module was 6ES7 153-2BA02-0XB0 / firmware v5.0 , the new one is 6ES7 153-2BA10-0XB0 / firmware v6.0 , i updated it in the hardware configuration 2- i set the dip switch in the new module as the old one " 3 " 3. operation mode on Master CPU. is DP master 4. the same cable wiring Attachment buffer.jpg (664 Downloads)
	Ahmed Atef
Suggestion To thank Quote Answer

7/15/2020 12:23 PM	Rate (0)
dchartier Grandmaster-Expert Joined: 9/27/2006 Last visit: 11/11/2024 Posts: 12293 Rating: (2691)	Hello Ahmed; The portion of the diagnostic buffer that you show indicates an I/O access error. This could mean the program in the CPU is trying to read or write to a "missing" Profibus slave. To understand this better, it would be good to see the details of the loggedessages in the buffer. Please use the Save As.. button in the diagnostic buffer, so that you generate a text file with the logged messages of the buffer, in great detail. If you attach this file to your next post, we can examine it and help you see what the CPU is complaining about. Could you also tell us the status of the diagnostic LEDs on the CPU and on the IM 153-2? Hope this helps, Daniel Chartier

Suggestion To thank Quote Answer

7/15/2020 1:06 PM	Rate (0)
Duris_I Diamond Member Joined: 4/28/2015 Last visit: 10/30/2024 Posts: 10585 Rating: (825)	Hello, how you did that change of ET modules? In case you delete previous and add new, you need configure in case of some parameters inside previous module to also new added. In other side again, you need rebuild your HW cfg and also probably SW rebuild and here I see problem in case that new module start occupy different addresses as you have inside your program. You need check everythink depended addresses and program. If you have some chance to see inside previous prj with old cfg ET200M, you can see probably different addreses, cfg, this is what I expect.
	With best regards... Ivan Duris Flight: OMICO
Suggestion To thank Quote Answer

8/3/2020 9:56 AM	Rate (0)
Ahmed_Atef. Advanced Member Joined: 7/23/2016 Last visit: 4/29/2024 Posts: 37 Rating: (0)	i uploaded the diagnostics file , please check Attachment Diagnostics.txt (642 Downloads)
	Ahmed Atef
Suggestion To thank Quote Answer

8/4/2020 8:53 AM	Rate (0)
Ahmed_Atef. Advanced Member Joined: 7/23/2016 Last visit: 4/29/2024 Posts: 37 Rating: (0)	Ahmed_Atef. i uploaded the diagnostics file , please check i created OB80/OB82/OB85/OB87/OB100/OB121/OB122 after that the CPU changed from stop to run mode and the new diagnostics file as attached any body can help me ? Attachment Diagnostics2.txt (667 Downloads)
	Last edited by: Ahmed_Atef. at: 08/04/2020 08:54:17 Ahmed Atef
Suggestion To thank Quote Answer

9/9/2022 11:51 AM	Rate (0)
Roozbeh21 Member Joined: 3/3/2019 Last visit: 9/9/2022 Posts: 1 Rating: (0)	Hi Ahmed Did you solve the problem ? I have the same problem, couldn't reach the IM153-2BA10 with CPU : 315-2AG10 Is this IM compatible with this cpu ?

Suggestion To thank Quote Answer

9/9/2022 7:31 PM	Rate (0)
Hati Platinum Member Joined: 9/21/2012 Last visit: 11/11/2024 Posts: 4195 Rating: (472)	Roozbeh21 Hi Ahmed Did you solve the problem ? I have the same problem, couldn't reach the IM153-2BA10 with CPU : 315-2AG10 Is this IM compatible with this cpu ? Is your profibus connection ok, can you see the node with accessible nodes?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

DP-Kommunikation

Follow us on