SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Download program to Sinumerik 810D

7/2/2007 6:30 PM	Rate (0)
Success Posts: 5 Rating: (0)	Hi I have a problem fordownloading my Sinumerik 810D with an old backup file. MyBackup file prepared by HMI Advanced but i have only "Sinucom PCin" for downloading the backup. My fileextension is "ARC".Firast i want to know is it possible that i use from "Sinucom Pcin" instead of "HMI Advanced". Second question :whenI start totransfer my program with Sinucom PCIN program. The transfer is correct only for about 1 minute and after that I have following Error on my Error Log. RS 232 C Error Log OK _N_AEDITOR_COM;$Path=_N_CST_DIR OK ......................................................... OK ......................................................... OK ......................................................... OK . . _N_C14_AWB;$Path=/_N_CST_DIR NC/PLC Error C1130356 Error with INI_File_Select in control-logic (NCA) Please Guide me fordownloadin my Sinumerik. also please guide me about configuring my CNC and PC for this transfer. Best Regards, Mohsen
Success Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/5/2007 4:49 PM	Rate (0)
pfuser Silver Member Joined: 9/18/2006 Last visit: 11/11/2024 Posts: 593 Rating: (64)	Hi. You try to edit an archival file means from Siemens. Successes

Suggestion To thank Quote Answer

7/17/2007 10:10 PM	Rate (0)
Success Posts: 5 Rating: (0)	Hi Please explain further . I did not undrestand.
Success Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/19/2007 3:00 PM	Rate (0)
pfuser Silver Member Joined: 9/18/2006 Last visit: 11/11/2024 Posts: 593 Rating: (64)	Hi. Try to make full NC-PLC reset before restoration of archive. Successes. P.S.You should be assured of working capacity of archive, you can try to correct archive the editor in WinPCIN.

Suggestion To thank Quote Answer

7/19/2007 8:31 PM	Rate (0)
Success Posts: 5 Rating: (0)	Dear pfuser Could you please explain what i have to change in archive file? Do you have complete Manuale of WinPCIN? Best Regards, Success
Success Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/25/2007 10:06 AM	Rate (0)
pfuser Silver Member Joined: 9/18/2006 Last visit: 11/11/2024 Posts: 593 Rating: (64)	Hi. Excuse me, I was mistaken. Not WinPCIN, and SinuCom ARC. Successes.

Suggestion To thank Quote Answer

7/26/2007 10:07 AM	Rate (0)
Pee Ell Sea Posts: 672 Rating: (57)	Hi, In a normal archive load no changes to the archive file are neccessary. So I suggest you do not try to edit the file. If you rebuild the file incorrectly it will not load because there are embedded checksums for file integrity. You say that you saved the file under HMI advanced. Are you now trying to load it into a system that has a PCU20 as the operators panel ?. If your 810 has an HMI advanced operators panel can you load the file onto the hard disk and try loading from there ? Are you loading the file in the series startup services area ?
Pee Ell Sea Posts: 672 Rating: (57)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users alex-krivonogov

Share this page:

Share this page on...