Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

transfer to new OP77B

Created by: Ziemens at: 3/21/2023 3:47 PM (5 Replies)

Rating (0)

Thanks 1

6 Entries

3/21/2023 3:47 PM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 11/7/2024 Posts: 944 Rating: (5)	Kindly, we have a new OP77B , and we need to download the project to it using Wincc Flexible 2008 and Mpi cable . We are seeing the panel well in the Set Pg Pc interface , but the project Transfer window shows no connection to the device . What could be the problem ? 6AV6641-0CA01-0AX1
	... thank you ...
Suggestion To thank Quote Answer

3/22/2023 7:18 AM	Rate (0)
Towome Platinum Member Joined: 7/9/2015 Last visit: 11/8/2024 Posts: 4022 Rating: (601)	Hi, in Chapter 7 of the following manual you find detailled informations about transfer project. Check settings. IMATIC HMI HMI device OP 73, OP 77A, OP 77B (WinCC flexible) Regards, Towome
	If my post was useful, please rate me - if not, please tell me - thank you!
Suggestion To thank Quote Answer

3/22/2023 7:59 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 11/7/2024 Posts: 944 Rating: (5)	Kindly, we are doing as described in chap7, using mpi 187.5kb, set pg pc detecting it, and the Op77b is transfer ready waiting for host. We tried with Prosave, but it is also not seeing the hmi. Could it be an issue that it is a new op, so we must use serial or usb cable for first time download?
	... thank you ...
Suggestion To thank Quote Answer

3/23/2023 9:31 AM	Rate (0)
Murof Platinum Expert Joined: 8/3/2009 Last visit: 11/8/2024 Posts: 14127 Rating: (1769)	Hello Ziemens The OP77B should have the dp drivers already installed also before you hae installed an Runtime project on it. Which settings do you have set in the OP itself? aciavte also "only master on the bus" Which communication processor or MPI/DP adapter/cable do you use exactly? which Image Version is on the Panel? (you can try to connect with prosave and read out the current image) (And do not! use the Auto setting in PGPC Interface setting, use Profibus OR MPI directly) Bye Murof
	Last edited by: Murof at: 03/23/2023 09:32:08 If this Information really helps, you could use the Rate function
Suggestion To thank Quote Answer

3/23/2023 11:07 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 11/7/2024 Posts: 944 Rating: (5)	The DP drivers looks installed (because the Set Pg Pc is seeing the hmi) ? The settings on the OP are: Channel 1 : Serial (un-changeable) -> Disable , Channel 2 : MPI/DP Enable (remote on) , Address: 1 , Baud rate: 187.5 kb , (Only Master on the bus is activated in PG/PC interface of the laptop) . The communication hardware is cable 6ES7901-0BF00-0AA0 connected to CP5711 of the PG . On the Panel screen we read image V11.00.02.02_01.05 (but could not connect with Prosave) . Bootloader : 1.02/30.1.2004 . In PG/PC interface, we used the MPI directly as mentioned . Could it be some versions issue (between op and prosave) ?
	Last edited by: Ziemens at: 03/23/2023 11:10:16 ... thank you ...
Suggestion To thank Quote Answer

3/24/2023 8:27 AM	Rate (0)
Ziemens Silver Member Joined: 3/2/2007 Last visit: 11/7/2024 Posts: 944 Rating: (5)	strangely, we tried another laptop, and it simply worked !!
	... thank you ...
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Murof

|

Share this page:

Share this page on...

Follow us on