Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Connection betwen S5-135U with CP1430-TCP and WinCC v6

Created by: Bruno Ayres at: 8/25/2006 1:53 PM (5 Replies)

Rating (0)

Thanks 0

6 Entries

8/25/2006 1:53 PM	Rate (0)
Bruno Ayres Posts: 7 Rating: (0)	Hi everyone! I need to connect WinCC v6 to a S5-135U PLC with a CP1430-TCP. The SINEC H1 cable must be connected to a RJ45 interface, so I made an adapter cable (6XV1 850-3LE50). Which connection I must use, CP1413-1, CP1413-2 or TCP/IP at WinCC side?. Does anyone know how I have to proceed to make this communication works? What are the configurations I have to do to make it possible? Thanks for atteniton!
Bruno Ayres Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

8/26/2006 12:10 AM	Rate (0)
Late Platinum Expert Joined: 1/7/2006 Last visit: 11/17/2023 Posts: 2705 Rating: (318)	[quote user="Bruno Ayres"]I need to connect WinCC v6 to a S5-135U PLC with a CP1430-TCP. The SINEC H1 cable must be connected to a RJ45 interface, so I made an adapter cable (6XV1 850-3LE50). Which connection I must use, CP1413-1, CP1413-2 or TCP/IP at WinCC side?. Does anyone know how I have to proceed to make this communication works? What are the configurations I have to do to make it possible? Hi Bruno, You need a cable thats on the CP143 TCP side a ITP and on the other side a RJ45, this cable have to be crossed when you don't use a switch.
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

8/29/2006 2:06 PM	Rate (0)
Bruno Ayres Posts: 7 Rating: (0)	Dear Late, I alredy made the adapter cable. But what I need to discover it is which software configuration I must make in the side of the CLP and the WinCC. In addition, I have installed the last version of SIMATIC NET in the side of the WinCC. Best regards.
Bruno Ayres Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

8/29/2006 3:22 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello, I think the best solution for you would be to contact the Win CC CoC in Erlangen. I can offer you also the following Link: http://www.industry.siemens.com/IT4Industry/EN/solution_services/SIMATIC_Addons/kanal.htm?PIdent=1075&SIdent=1003&TIdent=1024 There you will find Channel DLLs for such a use. You will have to purchase such a Channel. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

8/29/2006 3:57 PM	Rate (0)
Bruno Ayres Posts: 7 Rating: (0)	Thanks J_Bell. I have the SIMATIC S5 ETHERNET LAYER 4 driver. Can I use this channel? Thanks again!
Bruno Ayres Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

8/30/2006 11:10 AM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello, here you get a Brochure that explains some stuff.... SIMATIC WinCC Check for: SIMATIC S5 ETHERNET LAYER 4. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on