Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Teleservice and ethernet

Created by: Darius at: 4/14/2006 11:31 AM (6 Replies)

Rating (1)

Thanks 0

7 Entries

4/14/2006 11:31 AM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 10/22/2024 Posts: 2957 Rating: (242)	Hello, I have CPU-414 and teleservice connected to its profibus connection. There is CP443-1 (ethernet) module in the rack.So can I reach other cpu on the ethernet bus via teleservice? Thanks in advance. Best regards, Darius
	Best regards, Darius
Suggestion To thank Quote Answer

4/16/2006 12:15 AM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello Darius, if you have the latest Version of Teleservice, or better a Version 5.X or higher, with one of the latest Versions of Step 7 you should be able to do PG Routing. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

4/20/2006 7:56 AM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 10/22/2024 Posts: 2957 Rating: (242)	Hello, I have tried all variants, but nothing works. I have latest Step 7 and Teleservice software, but I can't do routing. Maybe there is some info about that? Best regards, Darius
	Best regards, Darius
Suggestion To thank Quote Answer

4/20/2006 10:54 AM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello Darius, would you explain to us what you tried, so it might be that someone can see what went wrong. Please tell us also what type (Order# and FW Version) of components (CPU, CP a.s.o.)you used to do the routing. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

4/20/2006 1:23 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 10/22/2024 Posts: 2957 Rating: (242)	Hello, I will try to explain. So I have CPU 414-3 DP (6ES7 414-3XJ04-0AB0). Teleservice TS-Adapter II is connected to master DP of that CPU. There are CP443-1 (6GK7 443-1EX11-0XE0). This module is connected to ethernet network. There is CPU 314C-2DP CPU (6ES7 314-6CF01-0AB0) on the same network. network is connected to CP343-1 (6GK7 343-1EX11-0XE0). So I try to use CP443-1 as gateway, but I can't go from profibus to ethernet. Best regards, Darius
	Best regards, Darius
Suggestion To thank Quote Answer

4/20/2006 1:52 PM	Rate (1)
J_Bell Posts: 5822 Rating: (412)	Hello Darius, actually, seen from the CPUs and CPs you use it should work. There is a little workflow how to solve this, have you tried this one yet? http://support.automation.siemens.com/WW/view/en/2383206 There check especially the Steps 3 to 6. Could you maybe send us a Screenshot of your Netpro configuration? Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer

4/20/2006 3:05 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 10/22/2024 Posts: 2957 Rating: (242)	Hello, Thanks for help. I think this link will help. I don't have a project right now so I can't do screenshot, but I think it will be no problems with this link that you gave. Thank you. Best regards, Darius
	Best regards, Darius
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on