Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

ERROR H system (1 out of 2) has gone into redundant mode

Created by: PLC2011 at: 8/7/2017 12:20 PM (8 Replies)

Rating (0)

Thanks 1

9 Entries

8/7/2017 12:20 PM	Rate (0)
PLC2011 Bronze Member Joined: 12/23/2011 Last visit: 11/22/2022 Posts: 143 Rating: (0)	HELLO in Diagnostic buffer cpu 412-5h this message "system(1 out of 2) has gone into redundant mode" Does it mean there is a fault or not? I read in the help program that the sync module probably has a problem Is that right? Thanks for your precious time Attachment 1.jpg (1213 Downloads)
	Last edited by: PLC2011 at: 8/7/2017 12:23:22 PM
Suggestion To thank Quote Answer

8/7/2017 12:21 PM	Rate (0)
PLC2011 Bronze Member Joined: 12/23/2011 Last visit: 11/22/2022 Posts: 143 Rating: (0)	PLC2011 HELLO in Diagnostic buffer cpu 412-5h this message "system(1 out of 2) has gone into redundant mode" Does it mean there is a fault or not? I read in the help program that the sync module probably has a problem Is that right? Thanks for your precious time Attachment 2.jpg (1125 Downloads)
	Last edited by: PLC2011 at: 8/7/2017 12:23:46 PM
Suggestion To thank Quote Answer

8/12/2017 12:55 PM	Rate (0)
PLC2011 Bronze Member Joined: 12/23/2011 Last visit: 11/22/2022 Posts: 143 Rating: (0)	please help me...

Suggestion To thank Quote Answer

8/13/2017 3:22 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	Dear user, The pictures you shared don't help that much to find out the entire scenario.Please save the diagnostics buffer of both CPUs as a text file and share them here to help you what is the exact cause of trouble.To do so, connect to each CPU,Select it in STEP 7 and CTRL+D.In the Diagnostics buffer tab , select Save as. I hope it helps, hdhosseini
	Demo Channel on Youtube
Suggestion To thank Quote Answer

8/15/2017 11:45 AM	Rate (0)
PLC2011 Bronze Member Joined: 12/23/2011 Last visit: 11/22/2022 Posts: 143 Rating: (0)	DEAR MR.HOSSEINI THE PICTURE FROM DIAGNOSTIC Attachment 3.jpg (1116 Downloads)

Suggestion To thank Quote Answer

8/18/2017 7:16 AM	Rate (0)
Ali00 Advanced Member Joined: 3/19/2015 Last visit: 10/2/2024 Posts: 22 Rating: (0)	Hi can you please check the CPU operation Mode (PLC> operation Mode), it will tell you if you system is running in redundant or not. diagnostic shows that one side of redundant H, master, has been restarted.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PLC2011

8/20/2017 7:33 PM	Rate (0)
PLC2011 Bronze Member Joined: 12/23/2011 Last visit: 11/22/2022 Posts: 143 Rating: (0)	hi the picture of operating mode: Attachment operating mode.jpg (1274 Downloads)
	Last edited by: Jen_Moderator at: 8/21/2017 9:01:41 AM
Suggestion To thank Quote Answer

3/25/2022 5:25 AM	Rate (0)
nkr Bronze Member Joined: 5/9/2015 Last visit: 10/28/2024 Posts: 81 Rating: (4)	Dear All, Is there any update on this issue. we are facing the same issue with the CPU 410-5H. Best regards, nkr

Suggestion To thank Quote Answer

10/22/2024 6:46 PM	Rate (0)
andreas.hall Member Joined: 4/6/2021 Last visit: 10/22/2024 Posts: 1 Rating: (0)	nkr Dear All, Is there any update on this issue. we are facing the same issue with the CPU 410-5H. Best regards, nkr Did you solve it? I have the same problem...

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on