Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Error measurement circuit of absolute corrent

Created by: Timóteo at: 12/15/2008 3:50 PM (15 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

12/15/2008 3:50 PM	Rate (0)
Timóteo Posts: 16 Rating: (0)	Hello all, I have a simodrive 611-A with now dispaly to me this error 300501 Axis C1 drive 5 error measurement circuit of absolute corrent. Some one was changing thinks in the machine and know i have the error... Is the drive fault, can be a software problem or switch configuration? Does anyone know what to do? Thanks Tim
Timóteo Posts: 16 Rating: (0)
Suggestion To thank Quote Answer

12/15/2008 4:10 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Select Error 300501 in Display then push the "HELP"-Button. Here you can read aditional help-Informations. (MMC103 and PCU50)
	Karl
Suggestion To thank Quote Answer

12/15/2008 4:15 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	What HMI do you have ? MMC103 ? PCU50 ? Do you have OLD Parameters from your Maschine ?
	Karl
Suggestion To thank Quote Answer

12/15/2008 4:19 PM	Rate (0)
Timóteo Posts: 16 Rating: (0)	Hello 300501 Axis C1 drive 5 error measurement circuit of absolute corrent. But i know the error the problem is that i dont know if it is a software or a hardware error... This hapen when i trie to turn the spindle motor manually on. Thanks Tim
Timóteo Posts: 16 Rating: (0)
Suggestion To thank Quote Answer

12/15/2008 4:37 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	>300501 Axis C1 drive 5 error measurement circuit of absolute corrent. You have an 611D NOT 611A ! ? >But i know the error the problem is that i dont know if it is a software or a hardware error... Do you have the same power-unit. Then you can twoogle both modules. Do you have you change Paramers ? >This hapen when i trie to turn the spindle motor manually on Tell me, how you can make this ??? Tell me the Siemens - Number from Power-Unit and controllercard.
	Karl
Suggestion To thank Quote Answer

12/15/2008 4:52 PM	Rate (0)
Timóteo Posts: 16 Rating: (0)	driver: 6SN1123-1AA00-0FA0 Control board: 6SN1118-0DG22-0AA0 NCU 572: 6FC5252-0AX21-0AB0 And an old MMC103: 6FC5253-0AB07-0AA0 Thanks Tim
Timóteo Posts: 16 Rating: (0)
Suggestion To thank Quote Answer

12/15/2008 5:29 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	>MMC103 O.K. Can you save actual NCK-Data in Archive After save NCK-Datayou can load an old NCK-Data from Archive. For Information: If you change NCK-Mada --> the old and Working NCK-Datas are loaded. Work the Maschine now ?
	Karl
Suggestion To thank Quote Answer

12/15/2008 5:36 PM	Rate (0)
Timóteo Posts: 16 Rating: (0)	Hello, I have a ghost of the drive of the MMC103... To make a copy of the NCU what software do i need? The machine is give me the same error... i think the drive is broken! Do you have the schematic/ service manual to fixe it? Thanks Tim
Timóteo Posts: 16 Rating: (0)
Suggestion To thank Quote Answer

12/15/2008 5:50 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	>Ihave a ghost of the drive of the MMC103... O.K. But you need it only, when the Harddisk is defekt. >To make a copy of the NCU what software do i need? There is on the MMC. Do you have the Password of manufactor. Set the manufactor - password. Go to "Dienste" (German-Language) Make IBN-Service >The machine is give me the same error... i think the drive is broken! >Do you have the schematic/ service manual to fixe it? Do you have DocOnCD ?
	Karl
Suggestion To thank Quote Answer

12/15/2008 6:03 PM	Rate (0)
Timóteo Posts: 16 Rating: (0)	hello, I have the disc of the mmc here conected to the pc with a usb adaptor, and now what to do? Idon't have the manufacter password... Dont have the DocOnCD to.. Thanks for your time! Tim
Timóteo Posts: 16 Rating: (0)	Last edited by: Timóteo at: 12/16/2008 9:10 AM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on