Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

FM355C problem with measurement!!! (termocouple)

Created by: andrewF at: 10/21/2008 1:37 PM (7 Replies)

Rating (0)

Thanks 0

8 Entries

10/21/2008 1:37 PM	Rate (0)
andrewF Posts: 87 Rating: (1)	I read others posts and not find answer to this question! I connect all wires like write in manual: all (- TC) to MANA and to M of CPU (M also connected to ground). I connect TC S to channel #1, channels 2, 3, 4 jumpered. TC near of controller and PT100 (connected for compensating). Linearisation - ON (standart TC S). And I have this: - temperature of cold junction =19C - T1 = 6 C (its not TRUE) - T2 = 5.2 C (its not TRUE) - T3 = -2.1 C (its not TRUE) - T4 = -5.4 C (its not TRUE) When I put ЕС to boiling water I have only 85C (its not TRUE). I read diagnostic data, through READ_355 function and I get this : see attachment. Voltage on jumpered input is negative...its absurd.... But normalisation I think worked..... Experts, help me!!!!!!!!!!! Attachment р1.JPG (253 Downloads)
andrewF Posts: 87 Rating: (1)
Suggestion To thank Quote Answer

10/21/2008 7:52 PM	Rate (0)
Gebhardt Karl Platinum Member Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	What TC do you have ? NiCrNi ? Typ K, J ? What ist the range of temperature from termocouple ?
	Karl
Suggestion To thank Quote Answer

10/21/2008 9:27 PM	Rate (0)
andrewF Posts: 87 Rating: (1)	I have 4 termocouple of type S ! I think work in range 1300 C (Termocouple with range to 1450C)
andrewF Posts: 87 Rating: (1)
Suggestion To thank Quote Answer

10/22/2008 11:50 AM	Rate (0)
Aret Posts: 2348 Rating: (264)	If you add temperaure of cold junction to measured temperaures from DB would they be TRUE? If you place wiring diagramm here it would be helpfull also...
Aret Posts: 2348 Rating: (264)	Last edited by: Aret at: 10/22/2008 11:51 AM
Suggestion To thank Quote Answer

10/22/2008 2:14 PM	Rate (0)
andrewF Posts: 87 Rating: (1)	In attach part of diagramm... What for I must load to DB????? In configuration menu I set "Reference input", but not "Parameters".....though I try it metods and I not see difference!! In previous post I write: "I think linearisation work", and I think adding temperature of cold junction also work.... I think problem in input circuits, like I write I see negative voltage in jumpered input.... and I not understanding this.... Attachment s.jpg (191 Downloads)
andrewF Posts: 87 Rating: (1)
Suggestion To thank Quote Answer

10/22/2008 6:30 PM	Rate (0)
Gebhardt Karl Platinum Member Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	With temperature are actual on it. 20°C ? If yes, please make the TC more than 250°C. What can you now read in Value. Is it possible, the wire are switch ? Please change the 2 TC-Cables ( 1 TC you have 2 Wire, ). What variavle you can now read.
	Karl
Suggestion To thank Quote Answer

10/22/2008 8:53 PM	Rate (0)
andrewF Posts: 87 Rating: (1)	Yes, near 20 C... I cant heat TC to 250C (i not have special device). but I control temperature by module 7kf02 and termocouple of type K and I have bolinig water = 97-98C....Also I can control this temperature by same TC and same wire(wire its special compemsating cable for TC S) by Universal controller and I have cold TC=near20C and heated TC=97C....... Please, lookto my previous post, what You think about negatve voltage on shorted (jumpered) input? Attachment inps.jpg (194 Downloads)
andrewF Posts: 87 Rating: (1)	Last edited by: andrewF at: 10/23/2008 7:06 AM Last edited by: andrewF at: 10/22/2008 9:08 PM
Suggestion To thank Quote Answer

10/27/2008 8:13 AM	Rate (0)
andrewF Posts: 87 Rating: (1)	Experts not help me and I cant find other solution for my problem, and I install converter to 4-20 mA.....its worked!
andrewF Posts: 87 Rating: (1)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on