Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Generate module drivers error

Created by: Tomact at: 4/19/2016 10:44 AM (8 Replies)

Rating (1)

Thanks 4

9 Entries

4/19/2016 10:44 AM	Rate (0)
Tomact Experienced Member Joined: 11/18/2015 Last visit: 1/20/2023 Posts: 81 Rating: (1)	Hello, When we try to compile with generate module drivers we get the error "Could not insert into connection between block PROMASS_83_DP_2/QACC_MODE and block PROMASS_83_DP_1/ACC_MODE". Now when I click on "Go To" I can find the block/IO PROMASS_83_DP_1/ACC_MODE but when I look at the block "PROMASS_83_DP_2" I can't find "QACC_MODE". Screenshots attached any help is appreciated! Attachment PROMASS_83_DP_2.png (97 Downloads)

Suggestion To thank Quote Answer

4/19/2016 10:50 AM	Rate (0)
mark1507 Platinum Expert Joined: 6/23/2008 Last visit: 4/28/2023 Posts: 1153 Rating: (267)	Hello Tomact, is it an upgraded project? What is the current version of your PCS7-project? Best regards...
	"Expert" does not necessarily mean Siemens employee. Please cross-check your requirements always with official Siemens documentation. Also "Experts" are pleased about feedback. Please don't send support requests as PM. Questioners who don't follow up their thread will be put to my list of users to be ignored.
Suggestion To thank Quote Answer

4/19/2016 10:55 AM	Rate (0)
Tomact Experienced Member Joined: 11/18/2015 Last visit: 1/20/2023 Posts: 81 Rating: (1)	Hello Mark, Yes this project came from PCS7 V6.1 and is now PCS7 V8.1

Suggestion To thank Quote Answer

4/19/2016 11:16 AM	Rate (0)
mark1507 Platinum Expert Joined: 6/23/2008 Last visit: 4/28/2023 Posts: 1153 Rating: (267)	Did you update the blocks to the current version? It looks like that the driver wizard is trying to connect old blocks from your project with new blocks from the library used by the wizard. So you should update at least all blocks used by the driver wizard in your project. The blocks used by the driver wizard come from the library "PCS7 Basis Library Vxy". Best regards...
	"Expert" does not necessarily mean Siemens employee. Please cross-check your requirements always with official Siemens documentation. Also "Experts" are pleased about feedback. Please don't send support requests as PM. Questioners who don't follow up their thread will be put to my list of users to be ignored.
Suggestion To thank Quote Answer

4/19/2016 11:33 AM	Rate (0)
Tomact Experienced Member Joined: 11/18/2015 Last visit: 1/20/2023 Posts: 81 Rating: (1)	Mark, All Siemens blocks are updated to the last version of the Siemens libaries. We also tried to delete all the "@Charts" so we're sure it can't try to connect to old blocks. Regards, TomAct.

Suggestion To thank Quote Answer

4/19/2016 11:38 AM	Rate (1)
mark1507 Platinum Expert Joined: 6/23/2008 Last visit: 4/28/2023 Posts: 1153 Rating: (267)	Did you perform a "Clean up" after deleting the @Charts? Make sure that there are no old blocks still recognized by CFC.
	"Expert" does not necessarily mean Siemens employee. Please cross-check your requirements always with official Siemens documentation. Also "Experts" are pleased about feedback. Please don't send support requests as PM. Questioners who don't follow up their thread will be put to my list of users to be ignored.
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Tomact Myst

4/19/2016 12:22 PM	Rate (0)
Tomact Experienced Member Joined: 11/18/2015 Last visit: 1/20/2023 Posts: 81 Rating: (1)	Mark, Thank you this fixed our error. I didn't know the driver blocks were only used in @Charts. So after our clean up he deleted all of the driver blocks. Now when we compile he places all the driver blocks himself (like its supossed to) and we didn't get an error! Thank you again! Regards, TomAct.

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users mark1507 Myst

4/19/2016 12:29 PM	Rate (0)
mark1507 Platinum Expert Joined: 6/23/2008 Last visit: 4/28/2023 Posts: 1153 Rating: (267)	Thanks for feedback
	"Expert" does not necessarily mean Siemens employee. Please cross-check your requirements always with official Siemens documentation. Also "Experts" are pleased about feedback. Please don't send support requests as PM. Questioners who don't follow up their thread will be put to my list of users to be ignored.
Suggestion To thank Quote Answer

3/21/2023 11:11 AM	Rate (0)
DirkMangelschots Member Joined: 3/19/2008 Last visit: 3/21/2023 Posts: 4 Rating: (0)	Hi Mark, what exactly do you mean by "clean up" after deleting all "@-charts"?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on