Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Logo 0BA8 and Mitsubishi E1101 HMI

Created by: omen1975 at: 10/11/2018 10:02 AM (9 Replies)

Rating (0)

Thanks 0

10 Entries

10/11/2018 10:02 AM	Rate (0)
omen1975 Posts: 24 Rating: (0)	Hi all. I would like to connect LOGO 0BA8 to Mitsubishi HMI E1101 panel. Outgoing signals from logo are made by VM mapping but how to read it by E-Designer ???? Someone help ?
omen1975 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

10/11/2018 10:09 AM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34202 Rating: (4260)	Hello omen1975, at first welcome to the forum. Have you any manuals? Has the designer a driver for Siemens S7 protocol?

Suggestion To thank Quote Answer

10/11/2018 10:35 AM	Rate (0)
omen1975 Posts: 24 Rating: (0)	I tried to find some instructions which step by step describe how to do it but I did not find it. I saw during my work on a ships that the Siemens S7-200-1200 supports Mitsubishi panels so I am sure that it is also possible to combine the LOGO. E-Designer has included dedicated drivers for Simatic. There is S7 ISO over TCP/IP and more... Attachment drivers.jpg (229 Downloads)
omen1975 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

10/11/2018 10:43 AM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34202 Rating: (4260)	The LOGO! can none of these protocols, also not "S7 ISO over TCP / IP". The LOGO! 0BA8 can only support Ethernet TCP/IP, as of LOGO! 8.1 FS04 additionally Modbus TCP / IP.

Suggestion To thank Quote Answer

10/11/2018 11:07 AM	Rate (0)
omen1975 Posts: 24 Rating: (0)	Ok, but LOGO is able to communicate with Simatic HMI panels by the same protocols as is for E1101. Means TCP/IP or by VM mapping. How it's done ??? https://www.youtube.com/watch?v=S8lXPR9AXE4
omen1975 Posts: 24 Rating: (0)	Last edited by: omen1975 at: 10/11/2018 11:07:54 AM
Suggestion To thank Quote Answer

10/11/2018 11:13 AM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34202 Rating: (4260)	omen1975 Ok, but LOGO is able to communicate with Simatic HMI panels by the same protocols as is for E1101. Means TCP/IP or by VM mapping. How it's done ??? https://www.youtube.com/watch?v=S8lXPR9AXE4 Yes, but only Ethernet TCP/IP as I wrote. It's not the same as S7 ISO over TCP/IP.

Suggestion To thank Quote Answer

10/11/2018 11:21 AM	Rate (0)
omen1975 Posts: 24 Rating: (0)	Ok. Thanks for info.
omen1975 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

10/11/2018 11:22 AM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34202 Rating: (4260)	If you see in the Video, the Siemens Panel is using a special communication Driver named "LOGO!". This based on S7 protocol by Ethernet TCP/IP.

Suggestion To thank Quote Answer

10/11/2018 12:24 PM	Rate (0)
omen1975 Posts: 24 Rating: (0)	Are You sure the LOGO is no able to use TCP/IP ??? I have found examples with similar HMI connected to LOGO by this protocol: https://www.blaja.cz/hmi-scada/vizualizace-logo-0ba7-s-touch-panelem-t4a.html https://www.youtube.com/watch?v=-gQ7yPxqaEM (page is in Czech language but can see chosed communication protocol SIMATIC S7 ISO TCP)
omen1975 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

10/11/2018 1:39 PM	Rate (0)
ixo65 Grandmaster-Expert Joined: 12/18/2014 Last visit: 11/12/2024 Posts: 34202 Rating: (4260)	If you mean, that is the same, then try and make it.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on