Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

MP 370 touch 12 inch

Created by: VVago at: 5/20/2014 9:54 PM (26 Replies)

Rating (1)

Thanks 13

Result pages:: |; 1 | 2 | 3; |

27 Entries

Entries per page: 10 | 20 | all

5/20/2014 11:16 PM	Rate (0)
VVago Posts: 784 Rating: (52)	Hello, 1-I will make OS update+Touch recalibration. 2-If fail,I will change the panel. 3- I have a copy of the program"programmedwith protool" 4-I make migration into MP 377using Wincc flexible 2008 SP2then migrating into Comfort panel using TIA portal V11 It is easy for me to do that. Best regards........
VVago Posts: 784 Rating: (52)
Suggestion To thank Quote Answer

5/20/2014 11:19 PM	Rate (0)
VVago Posts: 784 Rating: (52)	Abdalkader I faced the same problem once before and for my situation it wasn't any thing related to software it were the Hmi panel screw nails it were tied very tightly to the cabinet which affected the HMI panel touch , the problem solved after releasing the screws a little bit . It's very rare to happen but it may help
VVago Posts: 784 Rating: (52)
Suggestion To thank Quote Answer

5/20/2014 11:30 PM	Rate (0)
Ayman Elotaify Platinum Member Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	Wago Hello, 1-I will make OS update+Touch recalibration. 2-If fail,I will change the panel. 3- I have a copy of the program"programmedwith protool" 4-I make migration into MP 377using Wincc flexible 2008 SP2then migrating into Comfort panel using TIA portal V11 It is easy for me to do that. Best regards........ Another posibility which may save some money for you is to buy LCD touch screen. You will found new LCD touch screens with suitable prices here: http://www.ebay.com/itm/NEW-SIEMENS-MP370-12-1-6AV6-545-0DA10-0AX0-Lcd-Touch-Screen-Display-Glass-/251013980605 Hope this helps.
	Ayman Elotaify
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Ibrahim Fathy

5/20/2014 11:36 PM	Rate (0)
VVago Posts: 784 Rating: (52)	Thanks Ayman
VVago Posts: 784 Rating: (52)
Suggestion To thank Quote Answer

5/20/2014 11:53 PM	Rate (0)
Ayman Elotaify Platinum Member Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	You are welcome.
	Ayman Elotaify
Suggestion To thank Quote Answer

5/21/2014 4:37 AM	Rate (1)
IBN-Service Posts: 8946 Rating: (999)	Abdalkader I faced the same problem once before and for my situation it wasn't any thing related to software it were the Hmi panel screw nails it were tied very tightly to the cabinet which affected the HMI panel touch , the problem solved after releasing the screws a little bit . It's very rare to happen but it may help 100% Yes, that happens some times! If fixing screws tightened to hard, touch may have problems. So it is important to take care of the torque indication in assembly instructions.
IBN-Service Posts: 8946 Rating: (999)
Suggestion To thank Quote Answer
This contribution was helpful to 4 thankful Users SolutionFinder Ste39 Abdalkader Ibrahim Fathy

5/21/2014 10:50 AM	Rate (0)
VVago Posts: 784 Rating: (52)	IBN-Service Abdalkader I faced the same problem once before and for my situation it wasn't any thing related to software it were the Hmi panel screw nails it were tied very tightly to the cabinet which affected the HMI panel touch , the problem solved after releasing the screws a little bit . It's very rare to happen but it may help 100% Yes, that happens some times! If fixing screws tightened to hard, touch may have problems. So it is important to take care of the torque indication in assembly instructions. Thanks IBN-Service and Abdalkader
VVago Posts: 784 Rating: (52)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Abdalkader

5/21/2014 11:06 AM	Rate (0)
Nicky123 Posts: 59 Rating: (2)	Wago Hello, We have Simatic MP 370touch 12 inch Sometimes,the touch not work and weneed to turn power off then on many times. 1-What is the reason for this problem ? 2-What is the solution? Best regards........ Sometimes this problem may occur due to interference on communication. Once you start machine initially at that time may be heavy load motor or drives also starting. That create high noise and if your profibus or any communication cable between plc & hmi is passing through the same route then it may have high interference due to that it can hang the hmi. Once u restart the hmi it will be reset in hmi and again starts as usual bexcuse now ur heavy loads has already is startup condition. So it will not create high noise once it has been started.
Nicky123 Posts: 59 Rating: (2)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users SolutionFinder

5/21/2014 11:14 AM	Rate (0)
VVago Posts: 784 Rating: (52)	Nicky123 Wago Hello, We have Simatic MP 370touch 12 inch Sometimes,the touch not work and weneed to turn power off then on many times. 1-What is the reason for this problem ? 2-What is the solution? Best regards........ Sometimes this problem may occur due to interference on communication. Once you start machine initially at that time may be heavy load motor or drives also starting. That create high noise and if your profibus or any communication cable between plc & hmi is passing through the same route then it may have high interference due to that it can hang the hmi. Once u restart the hmi it will be reset in hmi and again starts as usual bexcuse now ur heavy loads has already is startup condition. So it will not create high noise once it has been started. In general, The communication cables (control cables) have a path differ from power cabes.
VVago Posts: 784 Rating: (52)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users SolutionFinder

5/21/2014 12:14 PM	Rate (0)
Ayman Elotaify Platinum Member Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	Nicky123 Wago Hello, We have Simatic MP 370touch 12 inch Sometimes,the touch not work and weneed to turn power off then on many times. 1-What is the reason for this problem ? 2-What is the solution? Best regards........ Sometimes this problem may occur due to interference on communication. Once you start machine initially at that time may be heavy load motor or drives also starting. That create high noise and if your profibus or any communication cable between plc & hmi is passing through the same route then it may have high interference due to that it can hang the hmi. Once u restart the hmi it will be reset in hmi and again starts as usual bexcuse now ur heavy loads has already is startup condition. So it will not create high noise once it has been started. Hello, I think interference may affect on the communication. It will not affecting on the touch screen.
	Last edited by: Ayman Elotaify at: 5/21/2014 12:50 PM Ayman Elotaify
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on