Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

PID controller ET200s

Created by: juriskg at: 9/11/2013 2:49 PM (5 Replies)

Rating (1)

Thanks 1

6 Entries

9/11/2013 2:49 PM	Rate (0)
juriskg Posts: 11 Rating: (0)	Hi, Im using et200s, and analog output6AG1 135-4FB01-2AB0. I have to control dc motor voltage, to get the ball in plastic tube on the desired height. The block CONT_C (Continuous controller) looks like too complicated. Is there some simple way to implement PID control in my project in TIA V11? Thanks in advance, Marko
juriskg Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/11/2013 5:47 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	juriskg Hi, Im using et200s, and analog output6AG1 135-4FB01-2AB0. I have to control dc motor voltage, to get the ball in plastic tube on the desired height. The block CONT_C (Continuous controller) looks like too complicated. Is there some simple way to implement PID control in my project in TIA V11? Thanks in advance, Marko Hello, PID controller in SIMATIC range of products can be selected based on type of input(continuous) and type of output (Continuous ,integrating or simple on/off actuators).Please, specify your application and input and output of algorithm. Best regards Hamid Hosseini
	Demo Channel on Youtube
Suggestion To thank Quote Answer

9/11/2013 6:10 PM	Rate (0)
juriskg Posts: 11 Rating: (0)	Hi, i have process, some kinde air levitation, where i need to control ball heigh in plastic tube (about 2m height of tube).I'm measuring the hight of the ball with laser sensor, which provides an analog output (1-10V), and I have to control the voltage on dc motor (1-7V) that is hooked up to the fan, which creates downforce, andpushes the ball up. Best regards, Marko
juriskg Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

9/11/2013 6:24 PM	Rate (1)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	juriskg Hi, i have process, some kinde air levitation, where i need to control ball heigh in plastic tube (about 2m height of tube).I'm measuring the hight of the ball with laser sensor, which provides an analog output (1-10V), and I have to control the voltage on dc motor (1-7V) that is hooked up to the fan, which creates downforce, andpushes the ball up. Best regards, Marko Hello, Despite the concerns about the signal types, I guess CONT_C can help you.The mentioned algorithm is really complex and that is essential for cases encountered for process regulation in industry. Best regards Hamid Hosseini
	Demo Channel on Youtube
Suggestion To thank Quote Answer

9/11/2013 6:28 PM	Rate (0)
juriskg Posts: 11 Rating: (0)	ThanksHamid for qucik answer. Best regards, Marko
juriskg Posts: 11 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users hdhosseini

7/7/2014 2:38 PM	Rate (0)
Narrator1 Bronze Member Joined: 3/25/2013 Last visit: 3/21/2019 Posts: 176 Rating: (1)	New question split intoHow can i implement PID controller for tempreture control. With best regards, Narrator1

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on