"PUROFIBUS" by "IM308-B"

Hello. Nokia
Thank you for giving a reply

Please let me know about your personal computer.
The name of a manufacture company, and form

I want to use "ET200" introduced by this thread.
The personal computer which I have is the desktop of DELL.
Windows 2000 and STEP5ver.7 are installed.
It was not able to start, even if it added the file of ET200 to this personal computer.

Are any good methods known?

Thank you

Hello!!

I got "PG710plus."

The monitor of "PG710plus" does not function.
It can use now by attaching a monitor outside.
I referred to this thread." PG710 plus VGA output"

Instantly, "COM ET200" introduced by this thread was installed.
And "COM ET200" was able to be started.

I am thankful to you who helped.

Hello

I am studying Profibus by IM308-B.
However, it does not work.

Form of apparatus

PG710Plus

RACK 6ES5700-2LA11
PS 6ES5951-7LB21
CPU 6ES5944-7UA21
DIGTALINPUT 6ES5430-7LA12 ←It is in No. 0 of RACK. 　Allotment by IM306 is I0.0 to I3.7.
PROFIBUS 6ES5308-3UB11 with ADAPTION CASING 6ES5491-0LB11　←It is in No. 6 of RACK.
EPROM 6ES5375-1LA21 ←IM308-B is equipped.
IM306 6ES5306-7LA11

ET200U 6ES5318-8MB13　←By COMET200, it is set as Station nummber:3.
BUS 6ES5700-8MA11　
DIGTALOUTPUT 6ES5441-8MA11 ←By COMET200, it assigns to Q10.0 from Q10.7.

The programs of CPU are the following contents.
I want to check that communication of PROFIBUS can be performed.

OB1
L IB0
T QB10
BE

The item set up by COMET200 was performed as follows.

F1: Entry of ET200 system parameter
ET 200 SYSTEM PARAMETERS
System name: profibus-test
Bus parameters:
Station number IM 308-B master module: 1
PG connected to bus: N
Second IM 308-B: N
Additional act. station: N
Baud rate: 187.5 kbaud
Bus profile: DP - Standard
Controller parameters:
CPU type: C
Response monitoring: Y 000.1 s
QVZ when station fails: Y
Diagnostics: Y Diagnostics address: 252
Dual-port RAM addr.: N Basic DPR page no.:
Ready signal:
Power up delay: 20 s

F2:Configuring
CONFIGURING
Station number: 3 Ares: P Station type: ET200U
Station name: et200u station 3
Next avaiable address DI: 10 Dq: 11 AI: 0 AQ: 0
Configuration: Module address I: Q:
0.8DQ 1.000 2. ......31.

From these contents, it saved C:TEST01ET.200.

EPROM 6ES5375-1LA21 prepared for IM308-B is set to Progr.No412.

On the screen of "F3 :Transfer functions"

Transfer partner: E(E)PROM / File
F1: Programming of memory submodule
Please enter the programming number of your memory submodule:

Just as it inputs 412

A display of "Wrong submodule or no submodule plugged in" comes out, and it does not progress previously.

STEP5 -- EPROM -- it can write in
direct EPROM from COMET200 -- it cannot write in

F4: Program file -> Binary file
Destination file A:TEST01BN.200　<---To a floppy disk
F6:ENTER
Evalution of diagnosis inCPU to DP standard? (<F3>: as in Versin 2)
F1.YES
Transmission completed

TEST01BN.200 recorded to the floppy disk,
the personal computer which can use USB-PROMMER 6ES7792-0AA00-0XA0
starting STEP5EPROMprogrammingV1.0.

STEP5 programfile/binaryfile
A:_TEST01BN.200
Load from binary file
Block A
programming number 412
Mode BYTE
start....Binary file transferred to module....

EPROM in which data was written is attached in IM308-B.
At this time, a power supply is turned off and the switch of IM308-B is in ST (Stop).
A power supply is turned on, and it waits until CPU rises.
RN (Run) lamp of CPU lights up.
At this time, the lamp of ST turns on IM308-B.
IM308-B is switched on to RN.
The lamp of ST begins blink and the lamp of IF begins to turn on IM308-B.

It has not worked by such situation.

Is a setup by COMET200 wrong?
Isn't data written in EPROM?

What is insufficient, as for me?
I want the advice from those experienced.
The data file created by ET200 and a binary file are appended.

2. Station number: 3 Ares: P Station type: ET200U in the IM318B.


Put the IM318B to standard DP and re-configure the I/O.
There should be a DIP switch for you to put the IM318B into standard DP mode.

br
kk