Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S5 programming cable

Created by: aliuta2000 at: 8/31/2010 11:27 AM (10 Replies)

Rating (1)

Thanks 1

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

8/31/2010 11:27 AM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 12/23/2024 Posts: 123 Rating: (4)	Hello , I realy need to build an S5 programming cable for an laboratory . can somebody provide me some diagrame for build such cable . i realy need an usb cable or if si not possible is ok also RS232 to S5 PLC
	Last edited by: aliuta2000 at: 8/31/2010 1:21 PM
Suggestion To thank Quote Answer

8/31/2010 8:36 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 12/30/2024 Posts: 10230 Rating: (1181)	Hello, Here you couldn't find pins descriptions. I suggest you to use original made cable. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

8/31/2010 8:37 PM	Rate (0)
jklm Platinum Member Joined: 12/22/2006 Last visit: 1/25/2022 Posts: 1742 Rating: (309)	Hello, The AS511 Interface of S5-CPUs is using current loop signals (TTY). You cannot make a TTY /RS 232 adaptation with just passive wiring. In other words you always need a special RS232 to TTY converter (or USB-TTY converter). The easiest thing to do is buy these special cables.
	Best regards jklm Suggestion was helpful? Feel free to rate it.
Suggestion To thank Quote Answer

8/31/2010 10:11 PM	Rate (1)
Vitas Posts: 74 Rating: (2)	Hi aliuta2000, for RS232/TTY cable trythis link or attachements: http://www.horter.de Cable RS232/TTY is simple to buildandUSB/TTY is very complicated, thereforeis better buy original cable. Good Luck Attachment TTY_cables.zip (3475 Downloads)
Vitas Posts: 74 Rating: (2)
Suggestion To thank Quote Answer

9/1/2010 2:12 PM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 12/23/2024 Posts: 123 Rating: (4)	Vitas Hi aliuta2000, for RS232/TTY cable trythis link or attachements: http://www.horter.de Cable RS232/TTY is simple to buildandUSB/TTY is very complicated, thereforeis better buy original cable. Good Luck Thanky you a lot for ....design . i will forget about USB to ...and i will try to build RS 232 /TTY cable . now (cause i did not work wit step 5 / only step7 )i will ask wich cable i need to build to program / read/write programm fro S5 PLC ???witout others devices ( TTY convertor or others devices). From what i have understood is need to build the activ one .is corect ??Or is ok to build only the passive (is easiest than activ ).
	Last edited by: aliuta2000 at: 9/2/2010 7:22 AM Last edited by: aliuta2000 at: 9/1/2010 2:28 PM
Suggestion To thank Quote Answer

9/2/2010 4:56 PM	Rate (0)
Vitas Posts: 74 Rating: (2)	Hi aliuta2000, usually You will connect directly to CPU ports and in this case is passive cable sufficient. But if You want connect to another S5 card e.g. IP246 Positioning Module, You have to use active cable, because port of IM246 has no current sources of 20mA that are necessary to supply ofpassive cable. Therefore usability of passive cable depend on type device to which You can connect. Good Luck Vitas
Vitas Posts: 74 Rating: (2)
Suggestion To thank Quote Answer

2/17/2011 11:22 AM	Rate (0)
smrana Posts: 13 Rating: (0)	sir u have try this tty circut and what the result thanks rana
smrana Posts: 13 Rating: (0)
Suggestion To thank Quote Answer

2/18/2011 2:04 PM	Rate (0)
Azteke0110 Posts: 376 Rating: (57)	Hello alitua2000, your write the following: “I will forget USB. I will try to buildRS 232 /TTY cable. Now (cause I did not work with step 5 / only step7). I will ask witch cable I need to build to program / read/write program from S5 PLC? Without others devices (TTY convertor or others devices). From what I have understood is need to build the active one. Is correct? Or is ok to build onlythe passive (is easiest than active)." -------------------------------------- I am a little confused now. Please describe exactly what you would like to realize. my questions are: 1. What is your softwareconfiguration on the PC (Laptop, Notebook)side? - Windows version? - STEP 5 software version? 2. What is your hardware configuration on the PLC side? - PLC type? - CPU type? If you have already a solution for your problem you do not need to answer. Best regards Gucci
Azteke0110 Posts: 376 Rating: (57)
Suggestion To thank Quote Answer

2/28/2011 9:23 AM	Rate (0)
aliuta2000 Bronze Member Joined: 1/26/2007 Last visit: 12/23/2024 Posts: 123 Rating: (4)	the issue was solved win xp s5/s7 for wind from IBH s5 cpu 95 RS 232 connection cable built Thx a lot and this thread can be deleted cause is solved the issue .
	Last edited by: aliuta2000 at: 2/28/2011 11:56 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users O_Moderator

11/2/2016 3:12 PM	Rate (0)
Wit_Moderator Moderator Joined: 8/21/2014 Last visit: 12/20/2024 Posts: 1035 Rating: (14)	New question published by khar1 is split to a separate thread with the subject TTY cable and connecting CPU 103U?. Best regards The Helping Hand
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards Wit_Moderator
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on