Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7-314C2 DP count AB encoder incremental

Created by: Aleksander EUTECH at: 1/2/2014 11:19 PM (6 Replies)

Rating (0)

Thanks 2

7 Entries

1/2/2014 11:19 PM	Rate (0)
Aleksander EUTECH Experienced Member Joined: 1/30/2013 Last visit: 3/17/2023 Posts: 33 Rating: (1)	Hi I have S7-314C2 DP and encoder incremental. Its A & B signals are connected to DI124.0 & DI124.1 (default), have TIA v12, I use COUNT_300C (SFB47), have soft gate, used type of input: rotary single encoder. Everything works except directions. No matter how I connect the signals A and B and spin encoder - they are always counted up without change direction unless if I change count direction inverted. Tryed on 2 new encoders. Please help, thank You!

Suggestion To thank Quote Answer

1/3/2014 10:47 AM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 3/24/2023 Posts: 4180 Rating: (1332)	Hi, Please, share us the printscreens of High speed configuration (Device View, CPU properites).
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

1/3/2014 1:30 PM	Rate (0)
Aleksander EUTECH Experienced Member Joined: 1/30/2013 Last visit: 3/17/2023 Posts: 33 Rating: (1)	I am sending printscreens. Compressed by WinRar. Attachment plc.zip (320 Downloads)

Suggestion To thank Quote Answer

1/3/2014 2:00 PM	Rate (0)
Marcjan Platinum Member Joined: 4/22/2010 Last visit: 12/15/2022 Posts: 5697 Rating: (702)	Hello, you have selected as signal evaluation rotary encoder single, make that rotary encoder quadruple. regards, Marcjan
	Problem solved? Please let us know! Please no technical questions by PM, use the forum sections for your questions.
Suggestion To thank Quote Answer

1/3/2014 2:55 PM	Rate (0)
Aleksander EUTECH Experienced Member Joined: 1/30/2013 Last visit: 3/17/2023 Posts: 33 Rating: (1)	Hi Marcjan I did rotary encoder quadruple and now my counter pulses twice, eg before was 100 pulses/100ms, now 200pulses/100ms, direction do not change when I am spining in two directions.

Suggestion To thank Quote Answer

1/4/2014 10:49 PM	Rate (0)
Aleksander EUTECH Experienced Member Joined: 1/30/2013 Last visit: 3/17/2023 Posts: 33 Rating: (1)	Hi again I read a technological instruction from S7-300, see that in every option: count continously, once or periodically counter is reverse so maybe I have bad wiring ;/ I dont know and will try in 2 days. That has now low priority for me but I want to know what is wrong. greetings!
	Last edited by: Aleksander EUTECH at: 1/5/2014 12:00 AM
Suggestion To thank Quote Answer

1/11/2014 11:54 AM	Rate (0)
Aleksander EUTECH Experienced Member Joined: 1/30/2013 Last visit: 3/17/2023 Posts: 33 Rating: (1)	Hello The matter clarified. It turned out that in the closet was mistakenly installed a two-level connector. It had two levels connected and the signals from another device overlapped with signals from the encoder. Therefore the reason for 3 encoder states (0log, intermediate (12.5 V) and 1log). In my defense I will add that I didnt build that cabinet. Used connectors are so similar to those installed incorrectly that a mistake could anyone make. After changing connectors the counter started counting correctly in two directions. Thank you for your help and best regards!

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users Marcjan vishal_panchal

|

Share this page:

Share this page on...

Follow us on