Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Screen not geting ON system 3

Created by: Nanu_333 at: 4/10/2012 11:31 AM (14 Replies)

Rating (0)

Thanks 4

Result pages:: |; 1 | 2; |

15 Entries

Entries per page: 10 | all

4/10/2012 11:31 AM	Rate (0)
Nanu_333 Bronze Member Joined: 5/19/2011 Last visit: 1/20/2023 Posts: 196 Rating: (5)	Dear expert, Beacuse I didnt get answer to previous thread I am creating new one. In my system 3 the screen is not geting ON so how to come out of this . I tried clear procedure as follow but couldnt suceed. A. CLEAR MEMORY PROCEDURE 1 STEP: "CANCEL"+2 2 STEP: "CANCEL"+3 3 STEP: "CANCEL"+4 B. NC INITIALIZE PROCEDURE 1 STEP "input"+5 2 STEP "input"+8 My system double nc model(comprise nc1 and nc2) Even I change the CPU board, & also the interace IO card(flat cable) between CRT & rack. Plz reply

Suggestion To thank Quote Answer

4/10/2012 8:48 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 12/20/2022 Posts: 1502 Rating: (176)	Hi It is a long time before. ( To check/repair a System 3). (And you have a 3TT - System ) Do you have an connector "NC ON" on/in the Sinumerik. (In/On the Power-Unit) What LEDs are ligth on the screen. What LEDs are light PLC. The screen working ? Regards Karl
	Last edited by: Gebhardt Karl at: 4/10/2012 8:50 PM Karl
Suggestion To thank Quote Answer

4/10/2012 9:28 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 12/20/2022 Posts: 1502 Rating: (176)	Hi Additional infos from you. rageshwari I have system 3 which I am recomissioning. The Screen is not getting On both PLC are in run mode but NC & screen is not ready. O.K. rageshwari This problem is common to all machine plz help/.. More machines ? Does the machines longer without power ? Regards Karl
	Karl
Suggestion To thank Quote Answer

4/11/2012 3:43 AM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 6/6/2023 Posts: 3380 Rating: (257)	only one I can remind you is check and change new bettery(s).
	Please Help me to understand your question!
Suggestion To thank Quote Answer

4/11/2012 6:19 AM	Rate (0)
Nanu_333 Bronze Member Joined: 5/19/2011 Last visit: 1/20/2023 Posts: 196 Rating: (5)	thanks for the reply, Yes you are write machines were off almost 2 year duration. I am sure that data is loss I have copied eprom to ram PLC program but what about screen it is not giving anything.No led on screen are blinking .the led blinks on screen only when the i press cancel key + 2,3,4 & input key + 5, 8 ..Even I have change operator interface card & NC perphery interafce card too. What is the solution now.We have change the battery also.I am attaching the rack picture in power ON condition plz look into it. Waiting for your reply. Attachment Photo-0263.jpg (312 Downloads)

Suggestion To thank Quote Answer

4/12/2012 9:11 AM	Rate (0)
Nanu_333 Bronze Member Joined: 5/19/2011 Last visit: 1/20/2023 Posts: 196 Rating: (5)	I solve the problem of screen.now i want to know what parameter i need to download(E.g seting data , R arameter etc). Is it possible to download all files by winpcin. plz reply.

Suggestion To thank Quote Answer

4/12/2012 11:12 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 5/7/2023 Posts: 8034 Rating: (855)	rageshwari I solve the problem of screen. plz reply. HOW?

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users O_Moderator

4/12/2012 1:29 PM	Rate (0)
Nanu_333 Bronze Member Joined: 5/19/2011 Last visit: 1/20/2023 Posts: 196 Rating: (5)	I was not knowing that the red color rotory switch I have to keep at position 1. Can u tell me how to load parameters through winpcin along with cable pin details.

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users O_Moderator PISCEAN 2010

4/12/2012 2:48 PM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 5/7/2023 Posts: 8034 Rating: (855)	rageshwari Can u tell me how to load parameters through winpcin along with cable pin details. Sorry, I am not familiar with older systems like 3M or 8M etc

Suggestion To thank Quote Answer

4/13/2012 8:14 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 12/20/2022 Posts: 1502 Rating: (176)	Hi rageshwari Can u tell me how to load parameters through winpcin along with cable pin details. Do you have PCIN ? If yes, you can push the Help-Button. Here you can find the differents types of cable. (DSub 9, Dsub25 . . .) Additional can you find the parameter for the System 3 - Parameters. (Baudrate, parity, stopbits . . . ) Regards Karl
	Karl
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on