Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

[SOLVED] S120 - Write traversing blocks params from Telegram

Created by: Joël Golinucci at: 3/22/2012 10:06 AM (5 Replies)

Rating (0)

Thanks 3

6 Entries

3/22/2012 10:06 AM	Rate (0)
Joël Golinucci Regular Member Joined: 3/22/2012 Last visit: 11/28/2024 Posts: 40 Rating: (0)	Hello, I'm trying to set parameters p2617, p2618, p2619 et p2620 (each time for sub param [0] and [1]) from data received by a custom telegram. The problem is that I cannot select those params from the telegram configuration window (these parameters are not listed, as shown in the attached screen shot). Does anyone know how could I set this (these are traversing blocks parameters) via a telegram sent over profibus from my Step7 program ? Or if this is not possible if there is any other way ? Many thanks, Regards, Joël Golinucci Attachment télégramme.JPG (387 Downloads)
	Last edited by: Joël Golinucci at: 3/26/2012 9:41 AM Post solved
Suggestion To thank Quote Answer

3/22/2012 10:12 AM	Rate (0)
Joël Golinucci Regular Member Joined: 3/22/2012 Last visit: 11/28/2024 Posts: 40 Rating: (0)	Sorry for repost, I forgot to say that I also tried to send these parameters via SFC58 and SFC59 (WR_REC/RD_REC). This works well on a S120 mono axe, but not on the book size version I'm using right now. The error codes returned from SFC58 seems to indicate that the transfert went well (first code 0x7001 then code 0x7002) but when I go online with Starter I see that my data aren't transferd. This is why I would prefer to use a telegram, and it's much more easy to set up ;-) Regards, Joël Golinucci

Suggestion To thank Quote Answer

3/23/2012 8:37 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 1/2/2025 Posts: 5975 Rating: (822)	Hello, you can use the Toolbox ("FB283"): Following the link: http://support.automation.siemens.com/WW/view/de/25166781
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

3/26/2012 9:40 AM	Rate (0)
Joël Golinucci Regular Member Joined: 3/22/2012 Last visit: 11/28/2024 Posts: 40 Rating: (0)	Hello, Finally I found the solution : I needed to use the first address defined in S120 in the SFC58/59. And in the record data header, I have to specify the Drive Object ID (= object number, for instance CU = 1, power unit = 2, axis one = 3, axis two = 4, ...). So I used SFC58, with LADDR set to the first one defined which in my case was the CU address. Even though I needed to address the axis one. Thanks for your help and time, Regards, Joël

Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users O_Moderator 0_Einstein Eru2

8/4/2017 12:47 PM	Rate (0)
satishmali Advanced Member Joined: 7/16/2016 Last visit: 11/25/2024 Posts: 8 Rating: (0)	dear sir , Can you send me backup of your program plc and starter for reference. pls help me.

Suggestion To thank Quote Answer

12/28/2020 12:36 PM	Rate (0)
Eru2 Member Joined: 9/19/2018 Last visit: 7/19/2024 Posts: 1 Rating: (0)	Hello, Can you tell me the exact name in which should I specify the object ID As you mentioned below For example(RECNUM or DATA RECORD) Object ID (= object number, for instance CU = 1, power unit = 2, axis one = 3, axis two = 4, ...)

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on