Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Starter V5.4 and CU240S-DP

Created by: Oliver.SvecMicka at: 8/6/2020 5:34 PM (10 Replies)

Rating (0)

Thanks 1

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

8/6/2020 5:34 PM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)	Hi All. I have Sinamics G120 ( PM240 ) with CU240S-DP. Old PM and CU was destroyed after strong storm. I replaced PM240 and CU240S-DP to a new one piece. But, i cant download my backup project to CU through "Starter V5.4 " because "Starter" cant see my CU. I cant connectiing to the CU and nothing.. If i check Accessible nodes, i see this one.: 3 - is a G120 Can anyone know, how can i download my back up project to the CU 240S-DP ?

Suggestion To thank Quote Answer

8/6/2020 8:28 PM	Rate (0)
zako_ Gold Member Joined: 5/22/2012 Last visit: 3/24/2022 Posts: 895 Rating: (67)	https://support.industry.siemens.com/cs/ch/de/view/44356870 Have used the Dip switches to configure the Profibus adress?

Suggestion To thank Quote Answer

8/6/2020 8:57 PM	Rate (0)
0_Einstein Diamond Member Joined: 7/7/2010 Last visit: 11/19/2024 Posts: 15406 Rating: (2446)	Don't G120's have a USB port in the front for situations like this? That's what I would do. Run a USB cable to my PG/PC (laptop) and install project after verifying the firmware matched what was in the project's G120.
	science guy
Suggestion To thank Quote Answer

8/7/2020 7:40 AM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)	zako_ https://support.industry.siemens.com/cs/ch/de/view/44356870 Have used the Dip switches to configure the Profibus adress? Yes, set node 3 ( dip 0 and 1 - ON, other - OFF)

Suggestion To thank Quote Answer

8/7/2020 7:49 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/18/2024 Posts: 22453 Rating: (3030)	Hi, can you create offline a CU240S-DP? Regards Christoph

Suggestion To thank Quote Answer

8/7/2020 7:52 AM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)	That project was created in :Starter 4.1 ( too old ) I have old laptop where i have is Starter 4.4. ( Win 7 ) But, if i look to the "Installed Devices" , that Devices is the same than in my version 5.4 ( my CU 240s-dp is missing ). Does anyone know, where i can download this version ? Starter 4.1 ? Does support this version on a 64bit system? ( Win 10 ) ?

Suggestion To thank Quote Answer

8/7/2020 7:58 AM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)	ChristophD Hi, can you create offline a CU240S-DP? Regards Christoph it is a strange, but yes.. if i create offline project, i must choose only CU240 and after it is possible choose version where is CU240S-DP ).

Suggestion To thank Quote Answer

8/7/2020 8:05 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/18/2024 Posts: 22453 Rating: (3030)	And if try to go online do this work? which devices are the other notes in the screen? Have you try to connect only the CU240 and test ot? Which FW Version is on the CU? Which PROFIBUS Adapter you use for Connection? Starter V4.1 is not available any longer for download (Out of support). Regards Christoph

Suggestion To thank Quote Answer

8/7/2020 8:20 AM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)	ChristophD And if try to go online do this work? which devices are the other notes in the screen? Have you try to connect only the CU240 and test ot? Which FW Version is on the CU? Which PROFIBUS Adapter you use for Connection? Starter V4.1 is not available any longer for download (Out of support). Regards Christoph i think, that will be a problem. I cant choose this node for download project because this node is unknown type for "starter"

Suggestion To thank Quote Answer

8/7/2020 8:22 AM	Rate (0)
Oliver.SvecMicka Advanced Member Joined: 4/27/2018 Last visit: 8/14/2024 Posts: 13 Rating: (0)
	Last edited by: Oliver.SvecMicka at: 08/07/2020 08:29:43
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users @AutoGen_953379

|

Share this page:

Share this page on...

Follow us on