Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

where i find RECORD DATA BLOCK RDREC

Created by: AZRAIQI at: 5/20/2014 4:55 PM (4 Replies)

Rating (2)

Thanks 3

5 Entries

5/20/2014 4:55 PM	Rate (0)
AZRAIQI Posts: 67 Rating: (1)	hi all, how i can getRecordData Block (RDREC) .... I work On recording data signal from CP1242-7 in other project i seen it but i dont know how to get it and the 2nd question what is the variable index and how to know other data indexs (for cp1242-7) .
AZRAIQI Posts: 67 Rating: (1)
Suggestion To thank Quote Answer

5/20/2014 7:58 PM	Rate (0)
hdhosseini Diamond Expert Joined: 1/28/2009 Last visit: 10/26/2024 Posts: 6852 Rating: (1365)	AZRAIQI hi all, how i can getRecordData Block (RDREC) .... I work On recording data signal from CP1242-7 in other project i seen it but i dont know how to get it and the 2nd question what is the variable index and how to know other data indexs (for cp1242-7) . There is a point to be shared regarding your question: TIA Online Help Note The interface of the "RDREC" instruction is identical to the "RDREC" FB defined in "PROFIBUS Guideline PROFIBUS Communication and Proxy Function Blocks according to IEC61131-3". This is the same case we have in STEP 7 (SFB52).Normally, We find details regarding the data record structure and index number in an application. Noramally, these are available in FAQs and manual for each hardware! I hope this helps, Hamid Hosseini
	Demo Channel on Youtube
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users AZRAIQI

5/21/2014 8:37 AM	Rate (0)
AZRAIQI Posts: 67 Rating: (1)	thanks for helping but i didnt get it exactly .. I have an old project used data record in it (not my project) (snapshut) 1- how to find this block and insert it in my TIA project ? 2- how to know the index number for "Signal Quality" in cp1242-7 ? (as i seen buy googled index number is 12336 for quality signal so my question from where this number) :D I sorry for asking again but .......
AZRAIQI Posts: 67 Rating: (1)
Suggestion To thank Quote Answer

5/21/2014 9:06 AM	Rate (2)
yy1 Gold Member Joined: 3/24/2009 Last visit: 7/9/2024 Posts: 535 Rating: (112)	AZRAIQI 1- how to find this block and insert it in my TIA project ? Dear AZRAIQI, 1) you can find the block in Extended instructions -> Distributed I/O 2) this depends on your module help Use the INDEX parameter to select the information to be read from the module. Which data records can be read with which data record number depends on the module. For additional information, see the manual to the specific module. For this specific index see FAQ Best regards, yy1
	Last edited by: yy1 at: 5/21/2014 9:14 AM added FAQ Last edited by: yy1 at: 5/21/2014 9:08 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users AZRAIQI

5/21/2014 9:46 AM	Rate (0)
AZRAIQI Posts: 67 Rating: (1)	thanks a lot :D
AZRAIQI Posts: 67 Rating: (1)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users yy1

|

Share this page:

Share this page on...

Follow us on