SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Wiring the Analog Input module 6ES7 431-1KF10-0AB0

12/21/2006 4:57 PM	Rate (0)
B.O.Z Posts: 3 Rating: (0)	Hello all, First of all, i searched everywhere to find how to wire an analog input module 6ES7 431-1KF10-0AB0. [:(] I have a little problem how to wire an Analog Input Module for the S7-400 PLC. [:o] You see, i have here a testpanel which contains a voltmeter for reading out the amount of volts and a variable resistor to variate between 0 to 10V. I have attached an drawing image of the testpanel. [:D] I want to connect the 0 - 10V on an analog input module 6ES7 431-1KF10-0AB0 so the PLC canmeasure the 0-10V. I already connected the +10Von pin 11 (M+) andGND on pin 12 (M-). And i connected the+24V on pin3 (L+)andGND on pin48 (M). If i monitor the variables (IW512, IW514 etc.) they are switching between -380 and -16? I hope someone can help me out here. Many thanks :) -B.O.Z- Attachment test_panel.JPG (1059 Downloads)
B.O.Z Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

12/22/2006 9:47 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 11/18/2024 Posts: 8770 Rating: (1171)	Hello, Here is a link to manual: http://support.automation.siemens.com/WW/view/en/1117740 see chapter 5.19 Is measuring module in right position? Is channel 0 disabled? Do not connect 24vdcand M (48) Have you seen this faq: http://support.automation.siemens.com/WW/view/en/20780602 Merry Christmas Wizard

Suggestion To thank Quote Answer

12/22/2006 4:23 PM	Rate (0)
B.O.Z Posts: 3 Rating: (0)	Thanks, i already solved it. The GND was not connected properly. When i reach the 10V the value IW514 (CH1) of the analog input module is 27648 When i reach 0V the value of IW514 (CH1) is 8? Is this correct? many thanks! and a Merry Christmas
B.O.Z Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

12/22/2006 4:48 PM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 11/18/2024 Posts: 8770 Rating: (1171)	Hello, The value for 10 Volt is correct, but a voltage of 0 volt would give a value 0. So I think there is a small voltage left. See manual from previous post, chapter 5 for analog representation to see values when you have 0-10 volt. Merry Christmas Wizard

Suggestion To thank Quote Answer

12/23/2006 6:40 PM	Rate (0)
Late Platinum Expert Joined: 1/7/2006 Last visit: 11/17/2023 Posts: 2705 Rating: (318)	Hi B, Thanks that you give the error thats made, so that others can learn about this. [8)] Normally there are real trouble with analog signals, most of the time it is wiring. [:cry:] Especially when PT100 are placed it is very importend that the Earth connections are very well, the measuring of mVolt is there what is measured. [:blush:]
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

Share this page:

Share this page on...