SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Time & Date Sync

11/27/2006 12:36 PM	Rate (0)
alexfizeau Posts: 95 Rating: (0)	How can I synchronize Time & Date of the OP (OP7)with the PLC (S7-300) ? Thanks.
alexfizeau Posts: 95 Rating: (0)
Suggestion To thank Quote Answer

11/27/2006 1:10 PM	Rate (1)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 12/24/2025 Posts: 9094 Rating: (1202)	Hello alexfizeau, Have you seen this faq: http://support.automation.siemens.com/WW/view/en/24086622 Best regards, Wizard

Suggestion To thank Quote Answer

11/29/2006 7:56 AM	Rate (0)
alexfizeau Posts: 95 Rating: (0)	Many thanks. What is the meaning of the following Message issued by the OP7 when I remove the Profibus-DP network cable: "$551SPS Address 2 Not Assigned" ? A. Is reffering to its own address ? B. Or to the default profibus address of the PLC, that is 2 ? I think the OP is searching for the PLC address (2), but I just wanted to be sure, by asking you masters. Thanks.
alexfizeau Posts: 95 Rating: (0)
Suggestion To thank Quote Answer

11/29/2006 9:26 AM	Rate (0)
Smurf Silver Member Joined: 9/28/2005 Last visit: 10/24/2024 Posts: 414 Rating: (28)	[quote user="alexfizeau"]Many thanks. What is the meaning of the following Message issued by the OP7 when I remove the Profibus-DP network cable: "$551SPS Address 2 Not Assigned" ? A. Is reffering to its own address ? B. Or to the default profibus address of the PLC, that is 2 ? I think the OP is searching for the PLC address (2), but I just wanted to be sure, by asking you masters. Thanks. Hi alexfizeau, Normally the HMI device watches the controller you defined in ProTool. So if you got that message that adress 2 is not assigned, you configured the controller at adress 2.
	Smurf "The only difference between a problem and a solution is that people understand the solution."
Suggestion To thank Quote Answer

11/29/2006 9:56 AM	Rate (0)
alexfizeau Posts: 95 Rating: (0)	[quote user="Wizard"]Hello alexfizeau, Have you seen this faq: http://support.automation.siemens.com/WW/view/en/24086622 Best regards, Wizard ok, many thanks
alexfizeau Posts: 95 Rating: (0)	Last edited by: alexfizeau at: 11/29/2006 10:47 AM
Suggestion To thank Quote Answer

11/30/2006 10:35 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 12/24/2025 Posts: 9094 Rating: (1202)	Hi alexfizeau, You are welcome. The message $551, means as you mentioned. The OP is searching for CPU with address 2, this means that the OP hasn't found the CPU yet. Best regards, Wizard

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PCMario

Share this page:

Share this page on...