09yu

i tried but not working

jonny_hantes

Hello

I am facing the same problem with the member WrenLiam, reported at 11/15/2017, about the a Logo.

I tryied also all the methods  mentioned from the expert, I also changed the program from standart to FS4. The code of the LOGO is 6ED1052-1HB00-0BA8 and the firmware version 1.81.3. Note that I reset the logo to factory setings, and when I chnge from OP to Admin and vise versa using the code LOGO it works.

Thanks

Hi all, 

I've faced this problem just after updating LSC to version 8.3 and using a brand new BM 8.2 FS:04.

After reading the quoted post I used the password LOGO (with all capitalized letters) and LSC accepted it, then I performed a factory reset and the password was no longer required.

Thanks jonny_hantes!

Murillo Gumiero

If your problem is cannot switch to Admin?

Go to:

Tools

Transfer

Clear User Program and Password 

Access control

Online Settings 

Control operation from the LOGO! TD

from here you can set new password.

then you can access CARD where you can upload ur program without using ur laptop .

Hope this helps.

Jemuel

Hello amontanochiara,

Thanks for answering in the topic!
For the next time please, try to discuss in English language. This is an international community, and we try to focus on one language. 

This is the translation of your answer:

amontanochiara

Excellent, proceed to perform the firmware update.

 Regards,
Jen_Moderator

FARAZ 928

من معمولاً هنگام اتصال به LOGO با این درخواست رمز عبور مواجه می شوم! دستگاه روی یک زیرشبکه متفاوت از شبکه‌ای که در حال حاضر در حین اجرای نرم‌افزار Comfort از آن استفاده می‌کنم.

به عنوان مثال، این سناریوها ممکن است آن را تحریک کنند:

الف: هنگامی که نرم افزار Comfort را در حالی که به زیرشبکه 192.168.1.XXX متصل هستم راه اندازی می کنم، اما سپس اتصال شبکه کامپیوترم را به 192.168.2.XXX تغییر می دهم و دستگاه Logo به زیرشبکه 192.168.2.XXX متصل می شود.

ج: زمانی که LOGO! دستگاه از طریق DNS پویا قابل دسترسی است و در همان شبکه رایانه من نیست.

به نظر می رسد که Comfort پس از تشخیص LOGO! در یک زیر شبکه متفاوت است، تلاش می کند با LOGO ارتباط برقرار کند! استفاده از پورت 8080 به جای پورت معمولی. این رفتار منجر به درخواست های رمز عبور مکرر برای هر عمل یا زیرعمل می شود.

اعمال برخی تغییرات در نرم افزار Comfort می تواند مفید باشد. مفید است که به کاربران اجازه دهیم رمز عبور خود را یک بار در هر جلسه وارد کنند، و سپس نرم افزار Comfort آن رمز عبور را برای بقیه جلسه به خاطر بسپارد و از آن استفاده کند، نه اینکه در هر عمل یا زیرعملی به طور مکرر آن را درخواست کند.

 Hello FARAZ 928,

welcome to the community! 

Please try to discuss in English language. This is an international community, and we try to focus on one language.

This is the translation of your post:

FARAZ 928

I usually get this password prompt when connecting to LOGO! The device is on a different subnet than the one I'm currently using while running the Comfort software.

For example, these scenarios may trigger it:

A: When I launch the Comfort software while connected to the 192.168.1.XXX subnet, but then I change my computer's network connection to 192.168.2.XXX and the Logo device to the 192.168.2.XXX subnet. Connects.

A: When LOGO! The device is accessible via dynamic DNS and is not on the same network as my computer.

It seems that after recognizing the LOGO! is on a different subnet, trying to communicate with LOGO! Use port 8080 instead of normal port. This behavior results in repeated password prompts for each action or subaction.

Applying some changes in the Comfort software can be useful. It is useful to allow users to enter their password once per session, and then have Comfort remember and use that password for the rest of the session, rather than repeatedly in each action or subaction. Request it.

 Regards,
Jen_Moderator