SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

sinamics v20 - I can't edit any parameters on BOP

5/18/2021 9:19 AM	Rate (0)
Katharsis171 Posts: 3 Rating: (0)	Hi, my sinamics v20 parameters editing is blocked on the display and I can't change just some of them (motor settings). Firmware version is v3.96 so I don't have parameter P0016 to unlock the BOP ( https://support.industry.siemens.com/cs/ww/en/view/109779917 ). Any ideas on how to unlock the parameters editing without firmware update? Is there any button combinations that work? ( the one in the link above doesn't)
Katharsis171 Posts: 3 Rating: (0)	Last edited by: Jen_Moderator at: 05/18/2021 11:02:36 Optimized link.
Suggestion To thank Quote Answer

5/18/2021 9:32 AM	Rate (0)
Mr.V Silver Member Joined: 6/19/2019 Last visit: 10/24/2025 Posts: 743 Rating: (79)	First go to Access level (P0003) and there choose 3 (Expert) then you can see and configure all parameters, also motor should be stopped if you trying configure motor parameters

Suggestion To thank Quote Answer

5/18/2021 9:55 AM	Rate (0)
Katharsis171 Posts: 3 Rating: (0)	it is set to 3 but it's still not working
Katharsis171 Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

5/18/2021 10:21 AM	Rate (0)
Mr.V Silver Member Joined: 6/19/2019 Last visit: 10/24/2025 Posts: 743 Rating: (79)	Did you try change parameter while motor stopped? sometimes not let change parameter if motor running. Did you read this: In addition to enabling parameter editing with P0016=0, you can alternatively use the BOP buttons to ena-ble the editing. Long-press OK (> 2 s), wait until "ULOC?" appears on the BOP display, and then press M. The unlocking becomes effective immediately.
	Last edited by: Mr.V at: 05/18/2021 10:26:10
Suggestion To thank Quote Answer

5/18/2021 12:19 PM	Rate (0)
Katharsis171 Posts: 3 Rating: (0)	i didnt connect a mottor to the inverter and the BOP buttons unlocking that you described isnt working :( nothing is happening
Katharsis171 Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

10/19/2022 11:06 AM	Rate (0)
Raidenn Posts: 1 Rating: (0)	Same problem with me. After doing factory reset, motor parameters (P304,305) cant be editted.
Raidenn Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

10/20/2022 5:22 AM	Rate (0)
Jack0004 Posts: 126 Rating: (2)	Hi Katharsis171 Enable commission mode and you can edit it Thanks Raidenn Same problem with me. After doing factory reset, motor parameters (P304,305) cant be editted.
Jack0004 Posts: 126 Rating: (2)
Suggestion To thank Quote Answer

10/27/2023 12:42 PM	Rate (0)
PeterBonder Joined: 5/28/2023 Last visit: 4/7/2025 Posts: 1 Rating: (0)	set P010 to 1 "quick commisioning"

Suggestion To thank Quote Answer

Share this page:

Share this page on...