Navigation

Tia portal plc sim can't connect

Created by: engco at: 1/31/2023 11:36 AM (8 Replies)

Rating (0)

Thanks 0

9 Entries

1/31/2023 11:36 AM	Rate (0)
engco Bronze Member Joined: 2/2/2016 Last visit: 2/8/2023 Posts: 221 Rating: (2)	I am doing simulation on Tia portal v16 but there is error connection message "An interface is not available for an online connection to the configured access node" PN/IE aren't available
	Last edited by: engco at: 01/31/2023 11:37:06
Suggestion To thank Quote Answer

1/31/2023 11:37 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/2/2025 Posts: 22709 Rating: (3071)	which versions you use? which PLC is simulated? any screen available for ther error?

Suggestion To thank Quote Answer

1/31/2023 11:41 AM	Rate (0)
engco Bronze Member Joined: 2/2/2016 Last visit: 2/8/2023 Posts: 221 Rating: (2)	I use v16 plc s71200 ChristophD which versions you use? which PLC is simulated? any screen available for ther error?

Suggestion To thank Quote Answer

1/31/2023 11:43 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/2/2025 Posts: 22709 Rating: (3071)	can you expand or copy the complete messagetext? is PLCSIM started? what shown in Online Access folder in the left TIA Portal Three?

Suggestion To thank Quote Answer

1/31/2023 11:55 AM	Rate (0)
engco Bronze Member Joined: 2/2/2016 Last visit: 2/8/2023 Posts: 221 Rating: (2)	yes, PLCsim started online access folder is empty. should i configure the ethernet network? ChristophD can you expand or copy the complete messagetext? is PLCSIM started? what shown in Online Access folder in the left TIA Portal Three?

Suggestion To thank Quote Answer

1/31/2023 11:57 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 9/2/2025 Posts: 22709 Rating: (3071)	have you start PLCSIM from TIA Portal or outside tia portal? normally if you start simulation of PLC the interface was set automatic to PLCSIM.

Suggestion To thank Quote Answer

1/31/2023 11:59 AM	Rate (0)
engco Bronze Member Joined: 2/2/2016 Last visit: 2/8/2023 Posts: 221 Rating: (2)	I start PLCSIM from TIA Portal ChristophD have you start PLCSIM from TIA Portal or outside tia portal? normally if you start simulation of PLC the interface was set automatic to PLCSIM.

Suggestion To thank Quote Answer

1/31/2023 12:14 PM

Rate (0)

engco

Bronze Member

Joined: 2/2/2016

Last visit: 2/8/2023

Posts: 221

Rating:

(2)

the complete error message

"An interface is not available for an online connection to the configured access node. PN/IE aren't available when ethernet cable is not connected or damaged"

8/12/2024 6:18 AM	Rate (0)
Cyclone 12 Joined: 10/18/2023 Last visit: 7/30/2025 Posts: 1 Rating: (0)	i have a similar issue any update on how you fixed the problem

Suggestion To thank Quote Answer

Share this page:

Share this page on...

SiePortal

Tia portal plc sim can't connect

Created by: engco at: 1/31/2023 11:36 AM (8 Replies)

Rating (0)

Thanks 0

9 Entries

engco

Last edited by: engco at: 01/31/2023 11:37:06

ChristophD

engco

ChristophD

engco

ChristophD

engco

engco

Cyclone 12

9 Entries

Follow us on

SiePortal

Created by: engco at: 1/31/2023 11:36 AM (8 Replies)

Rating (0) Thanks 0

9 Entries

Last edited by: engco at: 01/31/2023 11:37:06

9 Entries

Follow us on

Rating (0)

Thanks 0