SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Non system error

1/26/2010 3:02 PM	Rate (0)
A.T.A Posts: 24 Rating: (0)	Hi. As sinumerik is starting up,i want to go service menu but i face to error : *** non system disk or disk error **** replace and press any key when ready ****** I saw drive C and all of the needed files were. what's the problem? Thanks.
A.T.A Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

1/26/2010 7:58 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi Check BIOS Start options. If the Parameters from BIOS lose. (Data for Harddisk) If the "Switch" for lock Harddisk open. (MMC103 and PCU50) I hope you know what i mean.
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

1/26/2010 7:59 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Tell me what System. (840C, 840D, MMC103, PCU50 ....)
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

1/27/2010 2:05 PM	Rate (0)
A.T.A Posts: 24 Rating: (0)	Hi. Controller is 840D , and PCU50 , OP012:12,1" TFT bye.
A.T.A Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

2/2/2010 6:11 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi Harddisk is "disabled" ? (Switch on Harddisk)
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

2/4/2010 4:27 AM	Rate (0)
A.T.A Posts: 24 Rating: (0)	Hi. I read DocOnCD but i don't find how switch on Haradisk. Can you tell me how do it? Thanks.
A.T.A Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

2/4/2010 10:00 AM	Rate (0)
CNC600 Posts: 455 Rating: (77)	Please refer tothe attached image (PCU50). The knob has to be latched in the "unlock" position. hope that helps CNC600 Attachment PCU50.JPG (180 Downloads)
CNC600 Posts: 455 Rating: (77)
Suggestion To thank Quote Answer

2/10/2010 4:31 AM	Rate (0)
A.T.A Posts: 24 Rating: (0)	Hi The problem wasnot becuase of hard lock. It should be mentioned two points PCU doesn't run service menu and it runs Sinumerik and there isn't any problem working by HMI advanced. and the other is : this hard wasn't for PCU.becuase main PCU is defected so we installed its with an a new PCU. Thanks
A.T.A Posts: 24 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users S_Moderator

Share this page:

Share this page on...