Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

CPU 417-4H Halt

Created by: AbdulRahman at: 9/28/2011 1:55 PM (9 Replies)

Rating (0)

Thanks 0

10 Entries

9/28/2011 1:55 PM	Rate (0)
AbdulRahman Posts: 8 Rating: (0)	Dear Colleges, i have a problem with CPU 417-4H as Mentioned above actually all Leds LIT (ALWAYS ON) i accessed it through CP 443-1 IE ; the CP is OK as i tested it with a nother CPU I tried to remove the battery, switch off and on the Power supply switching the trigger switch in all Modes stop, Run, RunP nothing Changes
AbdulRahman Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

9/29/2011 9:55 AM	Rate (0)
Jazz_M Posts: 1121 Rating: (86)	AbdulRahman Dear Colleges, i have a problem with CPU 417-4H as Mentioned above actually all Leds LIT (ALWAYS ON) i accessed it through CP 443-1 IE ; the CP is OK as i tested it with a nother CPU I tried to remove the battery, switch off and on the Power supply switching the trigger switch in all Modes stop, Run, RunP nothing Changes Hi Well try this Please download the hardware Config via MPI port in CPU and check, Once i had the same problem where CP443-5 port was not being detected by the PG, It was a new CP card, so i downloaded it with MPI and then it started communicating with my PG. Have fun.....
Jazz_M Posts: 1121 Rating: (86)
Suggestion To thank Quote Answer

9/29/2011 10:56 AM	Rate (0)
AbdulRahman Posts: 8 Rating: (0)	thanks tagoloveri will try this
AbdulRahman Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

9/30/2011 8:20 AM	Rate (0)
Aret Posts: 2348 Rating: (265)	Sorry to say that. but actually all Leds LIT in most cases means DEFECTIVE state of CPU and that means you hace to change CPU
Aret Posts: 2348 Rating: (265)
Suggestion To thank Quote Answer

9/30/2011 4:42 PM	Rate (0)
gre_m Posts: 947 Rating: (45)	in DEFECTIVE state of CPU all led blink. I thing - need physical remove cp, optical link from hardware configuration and tested each CPU separately (only CPU, PS and rack). after this can read diagnostic buffer and begin find problem
gre_m Posts: 947 Rating: (45)	Last edited by: gre_m at: 10/1/2011 7:20 PM lost symbol is inserted
Suggestion To thank Quote Answer

9/30/2011 5:14 PM	Rate (0)
Amit_86 Posts: 1750 Rating: (272)	Dear Abdulrehman, i also doubt that your CPU is Defective.
Amit_86 Posts: 1750 Rating: (272)
Suggestion To thank Quote Answer

10/3/2011 3:40 PM	Rate (0)
Aret Posts: 2348 Rating: (265)	Well, i may be mistaken, but all LEDs blinking or constantly lit is abnormal for CPU - you wont find this mode in CPU manual.
Aret Posts: 2348 Rating: (265)
Suggestion To thank Quote Answer

10/3/2011 4:52 PM	Rate (0)
Marciano Silver Member Joined: 4/30/2007 Last visit: 6/17/2025 Posts: 231 Rating: (23)	All Led blinking not necessarily means defective, howevermeans thatsomething bad happened. Try to complete reset your CPU using the Clear/Reset from the Manager, and see if still possible some diagnostic for the Diagnostic Buffer.

Suggestion To thank Quote Answer

10/7/2011 2:57 PM	Rate (0)
Yer Posts: 86 Rating: (7)	Hi first start of an H-cpu takes a lot of timedepending of the amount of memory. In my case it takes 10 minutes!! during this time the cpu likes frozen. Yer
Yer Posts: 86 Rating: (7)
Suggestion To thank Quote Answer

10/7/2011 4:00 PM	Rate (0)
Aret Posts: 2348 Rating: (265)	Well, during first start i only saw STOP LED was blinking slowly (as if memory reset required). It's true - it lasts up to 20 mins, but with some indication present...
Aret Posts: 2348 Rating: (265)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on