SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Position/speed set point measurement

5/16/2012 7:26 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Hello Experts, In 840 controller with 611U drive can we see/check the axis position or speed set point value as an analogue value? If yes, how? Thanks in advance. DEEP.
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

5/16/2012 4:59 PM	Rate (1)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi PISCEAN 2010 In 840 controller with 611U drive can we see/check the axis position or speed set point value as an analogue value? If yes, how? Äh ? Sinumerik 840, 840C, 840Di, 840Dpl, 840Dsl . . . ? 611U --> With analog, Profibus DP .:. ? Sinumerik --> 611U What conektions for the speed ? Regards Karl
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

5/17/2012 5:10 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Opps Sorry, 840D,Di with 611U profibus. Regards, DEEP.
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

5/17/2012 7:42 PM	Rate (0)
Mr_Al Experienced Member Joined: 12/29/2011 Last visit: 9/17/2025 Posts: 39 Rating: (9)	You could use the DAU1 and DAU2 test sockets on the front of the 611U drive to output speed setpoint value as an analogue signal. Please note these test sockets are for Commissioning and Test - fault finding. Below is a link to the section of the 611u function manual which explains how to use them. https://www.automation.siemens.com/doconweb/pdf/SINUMERIK_SIMODRIVE_04_2010_E/FBU.pdf?p=755#page=755&view=FitBH,0&pagemode=none Best Regards Mr_Al

Suggestion To thank Quote Answer

5/18/2012 7:19 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Hello, Sorry its my fault. It is not 611U but its 611D.
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

5/18/2012 9:05 AM	Rate (0)
Mr_Al Experienced Member Joined: 12/29/2011 Last visit: 9/17/2025 Posts: 39 Rating: (9)	There are the same kind of Diagnostic test points on 611D. On the front of the 611D Control Card there are three test points DAC1 - 3 plus a fourth terminal which is the common reference ground. Here is a link to the section of the Drive Functions Manual which explains how to set up and use the DAC terminals. https://www.automation.siemens.com/doconweb/pdf/SINUMERIK_SIMODRIVE_04_2010_E/FBA.pdf?p=41#page=41&view=FitBH,0&pagemode=none Best Regards Mr_Al
	Last edited by: Mr_Al at: 5/18/2012 9:08 AM
Suggestion To thank Quote Answer

5/18/2012 9:19 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Hello, Once again thanks for your reply. I don't find any of those sockets on control moduls. The MLFB number of one of the control module is 6SN1118-0DM31-0AA1
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer

Share this page:

Share this page on...