Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

MM440 speed control problem

Created by: vishe5681 at: 8/22/2013 8:47 AM (12 Replies)

Rating (0)

Thanks 0

13 Entries

Entries per page: 10 | all

8/22/2013 8:47 AM	Rate (0)
vishe5681 Posts: 5 Rating: (0)	I have MM440 fitted with 7HP motor, till yesterday it was working fine. but today i can not cotrol the motor speed with potentiometer. when i give the run signal to drive its start with full speed and can not control the speed with potentiometer. ther is not fault massage on BOP. can anyone help me with this .
vishe5681 Posts: 5 Rating: (0)	Last edited by: vishe5681 at: 8/22/2013 9:00 AM
Suggestion To thank Quote Answer

8/22/2013 9:09 AM	Rate (0)
Marcjan Platinum Member Joined: 4/22/2010 Last visit: 3/31/2025 Posts: 5697 Rating: (716)	Hello, You can start with measuring the voltage at pin 2(-) and 3(+) if there is 10V, you have a problem with the potmeter or a short in the wiring. Regards, Marcjan Attachment mm440_pot.JPG (630 Downloads)
	Problem solved? Please let us know! Please no technical questions by PM, use the forum sections for your questions.
Suggestion To thank Quote Answer

8/22/2013 10:16 AM	Rate (0)
vishe5681 Posts: 5 Rating: (0)	i have checked voltage, it is pin 1-2 ----10V, pin 2-3-----0V, still motor is running with full speed, 1) if i start increase the voltage it is not going beyond 3.2V, 2) if i remove the cable from pin 3 and checked the voltage it is 0-10V (Depend to potentiometer setiing) 3) remove the cable from pin 3 and start the motor- motor running full speed can you tell me the what are parameter setting is required. can i reset the drive to factory setting and set the parameter again? any advice?
vishe5681 Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

8/22/2013 11:21 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hi Have you tried the down arrow on the BOP if you decrease the speed? Maybe someone has touched the parameter P 0700 that needs to be = 2. If you have all the parameters stored somewhere trying to do a reset to factory settings. By default P0700 = 2, which is the control terminal that is your potentiometer.

Suggestion To thank Quote Answer

8/24/2013 10:40 AM	Rate (0)
sparten Posts: 205 Rating: (11)	Hello vishes5681, first malke sure that your Port wiring at terminal is ok???for correct Port wiring pls find the attached file if it's ok then parameter setting on VFD for potentiometer referrence P700=2 P1000=2 P1070=755.0 after this setting moniter value of Port inParameter r752.0 also make DIP switch setting is ok or not?? Attachment PORT_WIRING.zip (550 Downloads)
sparten Posts: 205 Rating: (11)
Suggestion To thank Quote Answer

8/24/2013 8:02 PM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 6/7/2025 Posts: 1977 Rating: (479)	You can check as follows Check Value in P1000 - it must be 2 for analog 1setpoint If it is 2, then check value of analog input read by drive in r752. It should be matched with actual you measuring at terminals mentioned above - if not matching, check dip switches If everything looks fine, make sure Dataset change over is not programmed. Check value of P810. Regards, Devesh Vithani
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

8/25/2013 9:12 AM	Rate (0)
vishe5681 Posts: 5 Rating: (0)	Hi, can you tell me what should be DIP switch setting? parameter setting are following P700=2 P1000=2 P1070=755.0 P810=0 DIP SWITCH 1= ON DIP SWITCH 2= OFF in this condition motor dont have any control, i have make DIP switch 1= OFF, now i start the motor , motor start at full speed when i increase the potentiometer motor speed start decreasing. after 3.2 volt at pin 3 motor stop, if i futher increse the voltage at pin3 motor change its direction and increasing the speed.
vishe5681 Posts: 5 Rating: (0)	Last edited by: vishe5681 at: 8/25/2013 10:34 AM
Suggestion To thank Quote Answer

8/26/2013 12:57 AM	Rate (0)
Vithani Platinum Expert Joined: 7/8/2009 Last visit: 6/7/2025 Posts: 1977 Rating: (479)	Your DIP switch must be OFF because you are using voltage signal Also check setting in P756 Now, just check value in r752 and verify it is from 0 to 10 when you very it from potentiometer min to max Regards, Devesh
	I dont Like people driving Fast, thats the reason I overtake them ;)
Suggestion To thank Quote Answer

8/29/2013 8:30 AM	Rate (0)
vishe5681 Posts: 5 Rating: (0)	parameter setting are following P700=2 P1000=2 P1070=755.0 P810=0 r752= 0 to 10v (can very from potentiometer min to max) P756= 0 DIP SWITCH 1= OFF DIP SWITCH 2= OFF motor start at full speed when i increase the potentiometer motor speed start decreasing. after 3.2 volt at pin 3 motor stop, if i futher increse the voltage at pin3 motor change its direction and increasing the speed.
vishe5681 Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

8/29/2013 8:43 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hi vishe5681, have you tried to reset the drive to factory settings, and then replace all the parameters for your application?

Suggestion To thank Quote Answer

8/29/2013 9:06 AM	Rate (0)
vishe5681 Posts: 5 Rating: (0)	hi ok, i will try that, I want to run a motor from 0 to motor maximum speed with potentiometer control. can you tell me what are the basic parameter i need to set.
vishe5681 Posts: 5 Rating: (0)	Last edited by: vishe5681 at: 8/29/2013 9:08 AM
Suggestion To thank Quote Answer

8/29/2013 9:22 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 11/20/2024 Posts: 4620 Rating: (710)	Hi read what they told our friends and Vithani sparten, in the answers they gave you after the factory reset and then put your parameters.

Suggestion To thank Quote Answer

10/21/2015 4:06 PM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4759 Rating: (122)	New question published by AutoGen_921779 is split to a separate thread with the subject Control the speed of VFD 440 from the BOP. Best regards Min_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on