Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

WINAC RTX 2010 Sp2 and VM

Created by: LBEBENEK at: 3/15/2013 5:18 PM (68 Replies)

Rating (32)

Thanks 22

Result pages:: |; 1 | 2 | 3 | 4 | 5 |...; |

69 Entries

Entries per page: 10 | 20 | 50 | all

4/26/2013 10:50 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 9/16/2022 Posts: 40 Rating: (25)	Welcome. 1. uninstal all 2 install and when pc want reboot not accept and open wianc and make settings. 3 After make neccesary setiing -reboot. If not ,possible set reg key value . All need info is in attachment. PS I hope do you not have HP hardware? Check your VMx file to exist rom file line. Sometimes if you make restore from snapschot vmx setting was change. Attachment rtx.jpg (2713 Downloads)

Suggestion To thank Quote Answer

4/26/2013 10:55 PM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 9/16/2022 Posts: 40 Rating: (25)	Yes this config its OK. Finally check VMX file config. Because when i make restore points vmx config change in my solution. If You have HP hardware some people tell me to problems with them. Best regards. I hope to resolve Your problem.

Suggestion To thank Quote Answer

4/27/2013 11:21 AM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 2/12/2024 Posts: 40 Rating: (3)	Could you check please if VMware file settings and if i put on correct mode (under virtual machine folder) file ROM.Thanks.Regards.is not HP but DELL. Attachment 2013-04-27_111822.zip (2034 Downloads)

Suggestion To thank Quote Answer

4/29/2013 7:19 AM	Rate (0)
LBEBENEK Experienced Member Joined: 6/8/2011 Last visit: 9/16/2022 Posts: 40 Rating: (25)	Dr.Acrobat (no adobe) Could you check please if VMware file settings and if i put on correct mode (under virtual machine folder) file ROM.Thanks.Regards.is not HP but DELL. Welcom I check Your config. Rom file its Ok but You have ethernet0.virtualDev = "e1000". You must change to ethernet0.virtualDev = "e1000e". Your ROM file its correct location. Evrything loks fine. I have too DELL Host maschine. Try to run your rtx into schared mode maybe You can enter the RTX config. If You want of course its possible I can make remote support to check Your config on Your PC ( ex. Teamviewier). Best regards.

Suggestion To thank Quote Answer

4/29/2013 9:09 AM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 2/12/2024 Posts: 40 Rating: (3)	Don't worry be happy already installed on old laptop.Thanks.Regards.

Suggestion To thank Quote Answer

4/29/2013 2:24 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 2/12/2024 Posts: 40 Rating: (3)	Just last question : 6.Then From Step7 set IP addres from Menu --->PLC----> Edit Ethernet Node.When i try automatically system remove SET PG/PC Interface ETH from Step 7 and is not possible communicate with WinLC RTX.WINACRTX CARD.wld is OK?Thanks.Regards.

Suggestion To thank Quote Answer

4/29/2013 3:30 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 2/12/2024 Posts: 40 Rating: (3)	??? Attachment Untitled.jpg (2374 Downloads)

Suggestion To thank Quote Answer

4/29/2013 4:16 PM	Rate (0)
ZigoZago Advanced Member Joined: 5/19/2007 Last visit: 2/12/2024 Posts: 40 Rating: (3)	Solve PC internal Local.Thanks.Sorry for the apologyze.

Suggestion To thank Quote Answer

4/30/2013 7:36 PM	Rate (0)
FrankG Regular Member Joined: 5/30/2007 Last visit: 1/25/2023 Posts: 1 Rating: (0)	Hi, I have also set this up and would like to ask either one of you a question. Have you tried adding an OPC Server within your configuration? I have tried and can't get it to work. It allows, connections, OPC Server, etc. to be downloaded. But, you can't browse into the server either remote or local. It does not see the server with any client that I have tried while being on the local machine. Thanks in advance and have a great day. Frank

Suggestion To thank Quote Answer

6/11/2013 5:47 PM	Rate (0)
automatest Posts: 1 Rating: (0)	Per your instructions, the setup is done on VMware Workstation 9. I am using VMware Workstation 8. Is that going to work?
automatest Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

Result pages:: |; 1 | 2 | 3 | 4 | 5 |...; |

69 Entries

Entries per page: 10 | 20 | 50 | all

|

Share this page:

Share this page on...

Follow us on