Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Installing ProTool V6.0 SP3

Created by: rmonroe at: 4/16/2011 5:27 PM (6 Replies)

Rating (0)

Thanks 1

7 Entries

4/16/2011 5:27 PM	Rate (0)
rmonroe Posts: 22 Rating: (0)	I would like the install our ProTool V6.0 SP3onto a new PC. Do I have to transfer a license? If so where does the license resided? rmonroe
rmonroe Posts: 22 Rating: (0)
Suggestion To thank Quote Answer

4/18/2011 9:00 AM	Rate (0)
Sandman Platinum Member Joined: 4/29/2010 Last visit: 8/12/2024 Posts: 1557 Rating: (161)	Hello, at ProTool you just need a license for the Runtime. For installing and working with ProTool CS you don`t need a license. best regards

Suggestion To thank Quote Answer

6/3/2011 9:31 AM	Rate (0)
MavEric Bronze Member Joined: 5/28/2009 Last visit: 11/12/2024 Posts: 127 Rating: (10)	rmonroe I would like the install our ProTool V6.0 SP3onto a new PC. Do I have to transfer a license? If so where does the license resided? rmonroe Hi...rmonroe See the link............. https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid=19962184&caller=view
	Regards, SKD
Suggestion To thank Quote Answer

6/3/2011 2:04 PM	Rate (0)
Saravana kumar Gold Member Joined: 2/6/2009 Last visit: 8/19/2024 Posts: 939 Rating: (118)	Hi, I am sorry, please don't get me wrong. I don't know wheather your are aware of that the protool project can be migrated to WinCC flexible. Because nowadays we all having either Windows XP SP3 or Windows 7 as the operating system and the protool can work only in Windows Xp SP2. Thats why I have asked. If your intension is to open a protool backup you can use WinCC flexible itself. About protool you don't need any licensa for configuration. only for the RT license is needed.
	Last edited by: Saravana kumar at: 6/3/2011 2:07 PM _______________________________________________________________ Best Regards T.Saravana Kumar "All for the Best"
Suggestion To thank Quote Answer

6/3/2011 2:41 PM	Rate (0)
IBN-Service Posts: 8946 Rating: (999)	Saravana kumar ...the protool can work only in Windows Xp SP2. Thats why I have asked. ... ProTool V6.0 SP3 works very fine with WinXP SP3 also.
IBN-Service Posts: 8946 Rating: (999)
Suggestion To thank Quote Answer

6/3/2011 3:02 PM	Rate (0)
Saravana kumar Gold Member Joined: 2/6/2009 Last visit: 8/19/2024 Posts: 939 Rating: (118)	IBN-Service Saravana kumar ...the protool can work only in Windows Xp SP2. Thats why I have asked. ... ProTool V6.0 SP3 works very fine with WinXP SP3 also. Hi, Sorry for the mistake, But,I have seen the information about the operating system in the below link. In that link no where it says about Windows XP SP3, http://support.automation.siemens.com/WW/view/en/19962184
	_______________________________________________________________ Best Regards T.Saravana Kumar "All for the Best"
Suggestion To thank Quote Answer

6/3/2011 3:43 PM	Rate (0)
UMENCHO Diamond Expert Joined: 3/21/2006 Last visit: 11/1/2024 Posts: 10229 Rating: (1181)	Yes, officially Sp3 is not mentioned. But according to my expirience, I could confirm the same also. best regards, Hristo Mihalev

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Saravana kumar

|

Share this page:

Share this page on...

Follow us on