SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

RDREC does not work!

11/21/2013 11:34 AM	Rate (0)
Jens__ Posts: 39 Rating: (1)	Hello, I tried to use the RDREC but it does not work! First of all, it is strange that with the index that is an int and you can not set 16#802A direct to the input ? See picture, what have I done wrong ? Please help!! I tried to follow this document: http://support.automation.siemens.com/WW/view/en/38566021 Jens Attachment RDREC.jpg (285 Downloads)
Jens__ Posts: 39 Rating: (1)	Last edited by: O_Moderator at: 11/25/2013 8:34 AM new subject after splitting from /tf/WW/en/Posts/99132#top Last edited by: Jens__ at: 11/21/2013 1:56 PM Last edited by: Jens__ at: 11/21/2013 11:35 AM
Suggestion To thank Quote Answer

11/21/2013 2:06 PM	Rate (0)
Pittiplatsch Posts: 1368 Rating: (128)	Hello Jens_, at first view i see, that you configured the parameter "ID" with an INT, but DWORD is required. Change the "ID" 8177 to W#16#1FF1. Hope, it will work then Good luck, Pittiplatsch
Pittiplatsch Posts: 1368 Rating: (128)
Suggestion To thank Quote Answer

11/21/2013 2:13 PM	Rate (0)
Jens__ Posts: 39 Rating: (1)	Thanks Pittiplatsch. I have tried that also with no success. Do I need to do some settings somewhere ? What I want to do is to supervise the port status, if the cable is working or not that is connected to that port.
Jens__ Posts: 39 Rating: (1)
Suggestion To thank Quote Answer

11/21/2013 2:43 PM	Rate (0)
Pittiplatsch Posts: 1368 Rating: (128)	Hello Jens_, the ID must be the diagnostic address of the SCALANCE X204ld. Is that right? Do you get an error, if you set %M0.5 (RDREC.REQ) true? What is the state of RDREC after activating?
Pittiplatsch Posts: 1368 Rating: (128)
Suggestion To thank Quote Answer

11/21/2013 2:55 PM	Rate (0)
Jens__ Posts: 39 Rating: (1)	Thanks again! No, no error, see picture. I think the address is correct, see picture. I do not know what to check more ...¨ The status bytes what do they say ? 0070 02 00. 02 is that it is busy, but what does 70 mean ? Attachment picture1.jpg (195 Downloads)
Jens__ Posts: 39 Rating: (1)	Last edited by: Jens__ at: 11/21/2013 3:22 PM
Suggestion To thank Quote Answer

11/21/2013 3:49 PM	Rate (0)
Pittiplatsch Posts: 1368 Rating: (128)	Hello Jens_, i would not use the diagnostic address of port 1. Please try the address of the SCALANCE (8179) or of the interface (8178). Pittiplatsch
Pittiplatsch Posts: 1368 Rating: (128)
Suggestion To thank Quote Answer

11/21/2013 8:05 PM	Rate (0)
Jens__ Posts: 39 Rating: (1)	Thanks, I will try tomorrow, but in the document they put port 5's address, see picture. And the purpose of the function isto check what is connected to the port ? Attachment Document.jpg (137 Downloads)
Jens__ Posts: 39 Rating: (1)
Suggestion To thank Quote Answer

11/22/2013 10:53 AM	Rate (0)
Jens__ Posts: 39 Rating: (1)	The same result with 8179 and 8178. Not working :(
Jens__ Posts: 39 Rating: (1)
Suggestion To thank Quote Answer

2/8/2019 2:49 PM	Rate (0)
valerian.iosif Posts: 2 Rating: (0)	How did you solve the issue?
valerian.iosif Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...