SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Setting time/time zone in S7-1500

6/17/2014 11:11 AM	Rate (0)
jonbts Advanced Member Joined: 11/14/2013 Last visit: 10/15/2024 Posts: 15 Rating: (0)	Hello, I have the following problem, I try to set the time zone on my S7-1500, so I go the menú to configure it, I select my time zone, click OK and itlooks okay... for about a second. Then it goes back to 'not specified'. Why could this be? Same happens with 'Summer time' settings. In my TIA Portal I have also selected the time zone and when I load the program to the CPU the time zone doesn't change. Has anybody experienced something similar? The CPU is 1511-1PN, firmware 1.2 I think and I am using TIA Portal V12SP1 with the latest updates. Thanks for the help!
	Last edited by: jonbts at: 6/17/2014 11:11 AM
Suggestion To thank Quote Answer

6/17/2014 12:13 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 11/4/2024 Posts: 4351 Rating: (1452)	Hi, I'm not sure if I right undestood: did you say that you set the time zone and it comes back to original value? Offline or online?
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

6/17/2014 12:54 PM	Rate (0)
jonbts Advanced Member Joined: 11/14/2013 Last visit: 10/15/2024 Posts: 15 Rating: (0)	Yes, that is what happens. I enter the time zone using the screen of the PLC. I triedwith the PLC in RUN and alsoin STOP. It happens both ways.

Suggestion To thank Quote Answer

6/17/2014 5:00 PM	Rate (1)
Kelu Posts: 88 Rating: (12)	Hello jonbts, Are you changing time zone here? see picture In that way it should work after compile and load. Attachment Forum_TimeZone.jpg (2824 Downloads)
Kelu Posts: 88 Rating: (12)
Suggestion To thank Quote Answer

6/18/2014 7:43 AM	Rate (0)
jonbts Advanced Member Joined: 11/14/2013 Last visit: 10/15/2024 Posts: 15 Rating: (0)	Hello Kelu, Thank you for your reply. I have also tried this, but the PLC doesn'tsave the settings for the time zone after I load the Project.

Suggestion To thank Quote Answer

6/18/2014 8:53 AM	Rate (0)
Kelu Posts: 88 Rating: (12)	Hello, It's so strange... Perhaps try to upgrade with the last firmware V1.5.1 Regards,
Kelu Posts: 88 Rating: (12)	Last edited by: Kelu at: 6/18/2014 9:38 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users jonbts

6/20/2014 2:54 PM	Rate (0)
jonbts Advanced Member Joined: 11/14/2013 Last visit: 10/15/2024 Posts: 15 Rating: (0)	Hello, I updated the firmware and now it works fine! Thanks!

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users S_Moderator Eleu

Share this page:

Share this page on...