Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Delete PLC HW config

Created by: Sulung at: 8/23/2008 10:37 AM (9 Replies)

Rating (0)

Thanks 0

10 Entries

8/23/2008 10:37 AM	Rate (0)
Sulung Bronze Member Joined: 5/26/2007 Last visit: 11/8/2024 Posts: 127 Rating: (3)	Hi, i have configure my 315-2p to use both of the comm bus as profibus DP. But i wrongly set the both speed to 500Kbps. now i could not connect my laptop using pc adapter to my plc. How do i reset/delete the PLC HW config. I do not have a spare MMC. thanks in advance

Suggestion To thank Quote Answer

8/23/2008 4:07 PM	Rate (0)
legacy support Silver Member Joined: 7/15/2008 Last visit: 10/6/2024 Posts: 382 Rating: (44)	Hello Sulung I am assuming you have a CP5512 PCCard to communicate with the PLC .If yes , setyour PG\PLC Interface to 500kbaud and go Online with one of the DP Channels and Download the new Hardware configuration with thechanged Baudrate for the other DPChannel.

Suggestion To thank Quote Answer

8/24/2008 10:15 AM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	I think you are using a PC adapter. You can connect it to MPI port and go to Set PG/PC interface to PC adapter Auto or also in this case connect it to DP port It will work! reconfigure your boudrate and download it. I do not know If you are really using PC adapter or not, Please tell us. Regards,
	Ayman Elotaify
Suggestion To thank Quote Answer

8/25/2008 9:21 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 11/11/2024 Posts: 8768 Rating: (1170)	Dear sulung, Please have a look at this link: resetting the CPU in the as-delivered status See manual: http://support.automation.siemens.com/WW/view/en/13008499 Chapter 9.5 Best regards, Wizard

Suggestion To thank Quote Answer

8/26/2008 11:17 AM	Rate (0)
jboti Experienced Member Joined: 6/8/2007 Last visit: 10/24/2024 Posts: 54 Rating: (3)	Hi all, Wizard suggested Chapter 9.5 from the CPU31x Installation manual. Well, the resetting operation starts with ... Remove the SIMATIC Micro Memory Card from the CPU. But what happens if I put back the MMC into the CPU? (...since it can't work without a MMC) I couldn't find any description as to how to delete the contents of a MMC without the need to go online with the CPU. So the big question is, how to reset a CPU (including the MMC) if one can't communicate with it? Regards Boti

Suggestion To thank Quote Answer

8/27/2008 10:06 AM	Rate (0)
Ates Posts: 198 Rating: (17)	put switch to reset wait for blinks third blink will be longer then others when you see long blink, (at3rd sec) leave the reset switch and reset it again.. so hw will be deleted
Ates Posts: 198 Rating: (17)
Suggestion To thank Quote Answer

8/27/2008 1:49 PM	Rate (0)
JMJ Posts: 487 Rating: (45)	Ates put switch to reset wait for blinks third blink will be longer then others when you see long blink, (at3rd sec) leave the reset switch and reset it again.. so hw will be deleted This is wrong information. A MRES on a CPU with MMC will not clear HW config. You will have to use a PG to clear MMC or use Step7 todelete blocks manuallyit my going online with PLC. I would do that and then perform the factory reset procedure given by Wizard
JMJ Posts: 487 Rating: (45)	Last edited by: JMJ at: 8/27/2008 1:50 PM
Suggestion To thank Quote Answer

8/28/2008 1:07 PM	Rate (0)
Sulung Bronze Member Joined: 5/26/2007 Last visit: 11/8/2024 Posts: 127 Rating: (3)	Thanks everybody, I am using PC adapter, it's top speed is 187,5 kbps. What i need is to delete all the data in the MMC. I tried to do the hw reset, but once i put in my MMC, all of the configuration are transfer into the CPU. I still could not connect my plc to my laptop.

Suggestion To thank Quote Answer

8/28/2008 6:23 PM	Rate (0)
miami Platinum Expert Joined: 8/31/2005 Last visit: 10/22/2024 Posts: 2198 Rating: (328)	The S7-CPUs keep the station address and baudrate, even if you clear/reset the CPU. It will only change it, if the system data on the MMC is valid and has a other parametration. If you have Firmware 2.5 or higher you can use this. Just try it, if you are lucky you are back in the race. If you have a older firmware, you must reprogram the MMC. First: Watch the warning in this FAQ! You can reprogram the MMC - online with a S7-300 CPU and CP5512 (PCMCIA)or CP 5611(PCI) or - offline with the USB-programer or a SIMATIC PC (with MMC slot). If you know anybody, who has a Field-PG ask him to make a SIMATIC project with you CPU with MPI speed 187,5 kBit/s, compile it and copy it to the MMC. If you know anybody, who has a s7-300 CPU with PROFINET, you can use the online reprogramming using Ethernet instead of MPI.

Suggestion To thank Quote Answer

8/30/2008 9:07 AM	Rate (0)
Sulung Bronze Member Joined: 5/26/2007 Last visit: 11/8/2024 Posts: 127 Rating: (3)	Thanks everybody.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on