Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

810T PLC stop alarm

Created by: Import-User-1 at: 5/28/2010 9:15 AM (9 Replies)

Rating (0)

Thanks 3

10 Entries

5/28/2010 9:15 AM	Rate (0)
Import-User-1 Posts: 3609 Rating: (29)	Import of a Technical Question of an User Guest wrote: I have a Hardinge CHNC1 with 810T that was working just fine when I shut it down, but the next day when I started it up it has an alarm 3 PLC stop that I can't clear. Can some one tell me what might cause this alarm? Thanks, Danoland
Import-User-1 Posts: 3609 Rating: (29)
Suggestion To thank Quote Answer

5/28/2010 12:36 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi I think you Battery is emty. Urgent: Do NOT remove the Battery with Mainswitch Off ! ! ! Please check the Voltage from the Battery. (Lower Than 3,4 Volt? I the Batterie to low, you have lose NC and PLC Machine-Parameter. All LEDs on the MSTT are flashing ? (The Part with switch for Start, Stop, Reset) Error "No Conect with NC" Text on OP. Greatings
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

5/28/2010 10:13 PM	Rate (0)
Danoland Posts: 2 Rating: (0)	Hello Karl, I checked the battery it has 3.69v. Only the red LED with the ? is on. I don't have "No Conect with NC" on my screen. I only have 3 ORDPLC stop. Thanks, Dan
Danoland Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

5/29/2010 2:12 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Danoland Hello Karl, I checked the battery it has 3.69v. Only the red LED with the ? is on. I don't have "No Conect with NC" on my screen. I only have 3 ORDPLC stop. You mean realy a 840 T ? The machine is over 10 Years old. SORRY With my Infomation for the Voltage. Yesterday i have read 810D --> Battery is 3.6 Volt litiun You have a 810T --> 3 x Battery every 1.5 Volt. 3.69 Volt --> Battery is emty. URGEND Main-Switch must be ON when you renew the Battery ! ! ! If you have a luck you renew it. Then you check the Voltate after renewed Battery The Voltage must be greater than 4.5 Volt. URGENT: Check the correct sizeand "direction" from the Battery. After renew the Battery --> switch off and on the main switch. If you a "lucky boy" then the machine cant be working. If not, you have a problem, you have lose parameter. I'm wait for answer.
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Aviator_747

5/29/2010 3:37 PM	Rate (0)
pd_1 Posts: 20 Rating: (0)	Dear Friend, The message which is appearing on your screen shows that the PLC is in stop mode.Before we proceed i would like to know if you have the Data of the machine is with you. There will be three files NCMD , PLCMD and PLC PRG , if you have these three files then i can explain you how to load the files.
pd_1 Posts: 20 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Danoland

6/2/2010 11:21 PM	Rate (0)
Danoland Posts: 2 Rating: (0)	New battery fixed the problem. Thank you!
Danoland Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

6/4/2010 6:36 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi Danoland Danoland New battery fixed the problem. Thank you! The entrenchment after 1 Day is --> i think 50% More than 3 Days are lower than 30% ( i think) You need anyway a batterie ! Why not test your luck You are a "lucky Boy" or"lucky devil" ( what is the right namefor this word ? ) I think, you should play "lottery". Only for Information: There arein this Forum --> "Thanks"-buttons and "Rate"-buttons .
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer

6/4/2010 6:38 PM	Rate (0)
Gebhardt Karl Posts: 1502 Rating: (176)	Hi I have forgetted --> We enjoy/firward us for every feedback. greetings
Gebhardt Karl Posts: 1502 Rating: (176)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Danoland

11/12/2024 7:33 AM	Rate (0)
Klim-1991 Joined: 8/16/2024 Last visit: 12/28/2024 Posts: 4 Rating: (0)	Good afternoon, tell me, I have the same problem, error 3 ord plc-stop, but replacing the battery did not solve the problem

Suggestion To thank Quote Answer

11/14/2024 12:07 PM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 12/23/2025 Posts: 4566 Rating: (416)	Dear User please don't follow others. post you topic, give detail what happen? did you buy a new coming machine? or machine working good yesterday but alarm today? post picture of your screen AutoGen_1356572 Good afternoon, tell me, I have the same problem, error 3 ord plc-stop, but replacing the battery did not solve the problem
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on