Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Simens Simoreg K 6RA22 bench Testing without Motor

Created by: mmkhan at: 7/27/2010 1:04 PM (17 Replies)

Rating (2)

Thanks 1

Result pages:: |; 1 | 2; |

18 Entries

Entries per page: 10 | all

8/4/2010 8:31 AM	Rate (0)
mmkhan Bronze Member Joined: 9/28/2007 Last visit: 12/16/2025 Posts: 250 Rating: (13)	Dear Deep Thanks for your prompt response. i have set these parametes but drive is still showing -- . now i have changed P71=0 to 1. then Armatur output is enabled and voltage is increasing at output terminal.There is no need of changing of P39,P40 and jumper betweenX1:1 andX1:2becausei set these parameters to their previous values.now tell me that this drive is completley checked or it can shows error on colsed loop.i am waiting for your repsonse.
	Muhammad Munir Electronics Engineer
Suggestion To thank Quote Answer

8/4/2010 10:25 AM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (884)	256 Dear Deep Thanks for your prompt response. i have set these parametes but drive is still showing -- . now i have changed P71=0 to 1. then Armatur output is enabled and voltage is increasing at output terminal.There is no need of changing of P39,P40 and jumper betweenX1:1 andX1:2becausei set these parameters to their previous values.now tell me that this drive is completley checked or it can shows error on colsed loop.i am waiting for your repsonse. Hello, Congrats. How much is your AC 3 phase input voltage.? How much DC out put voltage is available at out put terminal.? You have to cross check these values. If those values are Ok then you can say that open loop test is Ok.Say e.g. if your AC 3 phase input voltage is 380 volt, you should get 400-420 DC out put voltage. If you want to check the drive in close loop, you need to connect DC motor, set the parameters accordingly & then conduct trial. Hope this answers to your query. All the best. DEEP.

Suggestion To thank Quote Answer

8/5/2010 6:00 AM	Rate (0)
mmkhan Bronze Member Joined: 9/28/2007 Last visit: 12/16/2025 Posts: 250 Rating: (13)	Dear Deep Thanks for your prompt response. voltages are ok.can you tell me the procedure of closed loop testing of drive without motor. i mean on 200 watt bulbs or etc or is it necessary to check thedrive in closed loop or it is fine that drive is working in open loop and i connect it on machine without testing on motor.i am waiting for your reply.
	Muhammad Munir Electronics Engineer
Suggestion To thank Quote Answer

8/5/2010 6:50 AM	Rate (0)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (884)	To the best of my knowledge, their is no any method to check any drive in close loop method without connecting any motor since it is very difficult to simulate speed as well as current feedbacks precisely. DEEP.

Suggestion To thank Quote Answer

8/5/2010 8:21 AM	Rate (0)
mmkhan Bronze Member Joined: 9/28/2007 Last visit: 12/16/2025 Posts: 250 Rating: (13)	Dear Deep Thanks for your answers.wish you good luck.i am still searching the procedure of dc drive testing without motor. best regards
	Muhammad Munir Electronics Engineer
Suggestion To thank Quote Answer

8/5/2010 1:36 PM	Rate (0)
O_Moderator Diamond Member Joined: 4/24/2009 Last visit: 8/20/2024 Posts: 2682 Rating: (135)	Just for all of you. I splitted the manual sent to me by DEEPSTR2010 into two parts. Best regards O_Moderator Attachment 6RA22 drive manual(1).zip (631 Downloads)
	Tips&Tricks for the forum usage
Suggestion To thank Quote Answer

8/5/2010 1:37 PM	Rate (1)
O_Moderator Diamond Member Joined: 4/24/2009 Last visit: 8/20/2024 Posts: 2682 Rating: (135)	part2 Attachment 6RA22 drive manual(2).zip (613 Downloads)
	Tips&Tricks for the forum usage
Suggestion To thank Quote Answer

8/6/2010 7:37 AM	Rate (1)
PISCEAN 2010 Diamond Member Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (884)	256 Dear Deep Thanks for your answers.wish you good luck.i am still searching the procedure of dc drive testing without motor. best regards Hello 256, Wish you all the best for your search. However if you come accross any method to test drive without motor, please donot forget to share it with us. DEEP.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on