SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Configure DP in STEP 7

2/17/2009 6:23 AM	Rate (0)
DeatHWilL Posts: 31 Rating: (0)	Hi everyone, With CP50M0,i can use com profibus to configure the CP50M0 as a DP master for connecting a drive,meanwhile as a DP slave for connecting another DP master. And what can i do this with CP50M1 in STEP 7? Thanks in advance!
DeatHWilL Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

2/17/2009 6:40 AM	Rate (0)
KSN Diamond Expert Joined: 8/25/2006 Last visit: 12/18/2025 Posts: 2221 Rating: (282)	In CFC (not in Step7) you must configure all DP telegrams related to this CP50M0.

Suggestion To thank Quote Answer

2/17/2009 10:11 AM	Rate (0)
DeatHWilL Posts: 31 Rating: (0)	Thank you KSN, And can you tell me about how can i configure the topology in STEP 7?I know how can fix it using com profibus,but what can i do in STEP 7.
DeatHWilL Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

2/17/2009 10:30 AM	Rate (0)
KSN Diamond Expert Joined: 8/25/2006 Last visit: 12/18/2025 Posts: 2221 Rating: (282)	All DP topology is configured in Com Profibus. You need not do anything in Step7 or NetPro. You must only select the bus type (MPI/PROFIBUS, in your case - PROFIBUS)in properties of CP50M0 in HWConfig.

Suggestion To thank Quote Answer

2/17/2009 1:32 PM	Rate (0)
ricardo76 Posts: 2 Rating: (0)	Hello, I know that I need to make all communications for CP50M0 with COM PROFIBUS. ( I did it allready) What is with CP50M1 ? Is it the same story ? I need to connect do DP / DP coupler to CP50M1. I assume I need to parametrise in the same way over COM PROFIBUS. Do I need some extra GSD data ? Thank you in advance
ricardo76 Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

2/17/2009 3:51 PM	Rate (0)
miami Platinum Expert Joined: 8/31/2005 Last visit: 12/16/2025 Posts: 2198 Rating: (331)	For the CP50M0 you need COM PROFIBUS to setup the bus configuration. The CP50M0 can be Master and Slave at the same time. For CP50M1 you use the STEP7 Tools HWConfig and NetPro to setup the bus configuration. The CP50M1 can be master or slave, but not both an one time.
	Last edited by: miami at: 2/18/2009 6:01 PM
Suggestion To thank Quote Answer

2/18/2009 2:07 AM	Rate (0)
DeatHWilL Posts: 31 Rating: (0)	Oh! I pretty much understand it! Thank you guys!
DeatHWilL Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...