Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S5-110 plc error

Created by: Konstantinos Egk at: 7/30/2023 3:04 PM (11 Replies)

Rating (3)

Thanks 0

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

7/30/2023 3:04 PM	Rate (0)
Konstantinos Egk Member Joined: 10/30/2021 Last visit: 7/30/2023 Posts: 6 Rating: (0)	Hello i am facing the following problem, is any chance someone has any clue how to fix it? Attachment εικόνα_Viber_2023-07-30_18-03-03-826.jpg (517 Downloads)

Suggestion To thank Quote Answer

7/30/2023 4:20 PM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 11/11/2024 Posts: 34191 Rating: (4260)	The operating instructions for the S5-110A say in the "Troubleshooting" section: Either the central module is defective (replace) or the NC battery is defective (replace).

Suggestion To thank Quote Answer

7/30/2023 5:30 PM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 11/11/2024 Posts: 34191 Rating: (4260)	I upload the manual of the S5-110A to my cloud. You can download from here: S5-110A Operating instructions Take a look at page 31.

Suggestion To thank Quote Answer

7/30/2023 6:19 PM	Rate (0)
Konstantinos Egk Member Joined: 10/30/2021 Last visit: 7/30/2023 Posts: 6 Rating: (0)	First of all Sir thank you for your fast responce . As i read the diagram its like a battery fault probably is there any guide where the battery on this plc is? I searched on it but couldnt find it.

Suggestion To thank Quote Answer

7/30/2023 6:34 PM	Rate (1)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 11/11/2024 Posts: 34191 Rating: (4260)	It's a battery unit. Take a look at page 30.

Suggestion To thank Quote Answer

7/30/2023 6:38 PM	Rate (0)
Konstantinos Egk Member Joined: 10/30/2021 Last visit: 7/30/2023 Posts: 6 Rating: (0)	One more question , If the program is lost with the buttons can i move the program again from eprom back to the cpu ? Moreover when i went to see the problem on the machine cpu was on stop , is it possible that the plc was working on stop mode?

Suggestion To thank Quote Answer

7/30/2023 6:44 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 11/11/2024 Posts: 34191 Rating: (4260)	In the stop state, the PLC cannot process a program. The command output is blocked and no outputs are switched on. The program is stored on the EPROM.

Suggestion To thank Quote Answer

7/30/2023 6:48 PM	Rate (0)
Konstantinos Egk Member Joined: 10/30/2021 Last visit: 7/30/2023 Posts: 6 Rating: (0)	So someone tried tried to fix and switched plc to stop, the other switch needs to be on NR OR R , to let plc read program from eprom?

Suggestion To thank Quote Answer

7/30/2023 6:51 PM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 11/11/2024 Posts: 34191 Rating: (4260)	Can't tell from afar... I'm not Jesus...

Suggestion To thank Quote Answer

7/30/2023 6:54 PM	Rate (0)
Konstantinos Egk Member Joined: 10/30/2021 Last visit: 7/30/2023 Posts: 6 Rating: (0)	No i may didn't said the quastion right. What is NR and what is R on the cpu ?

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on