Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7 315-2 DP comm problems with Open Modbus/TCP

Created by: pollo_rdz at: 4/25/2012 3:17 AM (16 Replies)

Rating (1)

Thanks 0

Result pages:: |; 1 | 2; |

17 Entries

Entries per page: 10 | all

4/25/2012 3:17 AM	Rate (0)
pollo_rdz Posts: 8 Rating: (0)	Hello all, I have tried to communicate my PLC S7 315-2 DP as Client with Open Modbus to Delta V, I have followed the procedure to register the PLC with the Siemens license according to the manuals successfully, but still not getting communication Previously I have an HMI connected to a pasive read write TCP connections 01 and 02 and this is working correctly, and I created a third connection for the Modbus device, and the local port 202, I have a Vat table to monitor the parameters, and I can see that when I enable the ENQ_ENR and the WRITE_READ bits, I start getting error and the status I observe is W#16#8183, I used a Omni MBT Modbus Tester, but I was not able to receive or send,or even see the PLC, The Hardware I'm using is: PLC 315-2 DP 343-1 Ethernet card connected with port No1, IP address 10.168.129.115, connected to a Ethernet Switch HMI Proface 3500 series, Ethernet Connetion, IP address 10.168.129.18 The Modbus Server IP 10.168.129.104 with remorte port 502. , is there anybody who could give me some advice on how to trace ot troubleshoot the system. My questions should be, is there a proper order to create the communication connection?, should I need to install another independent 343-1 card in my system in order to have a different segment for Modbus connection or how should I define the hardware in order to get a Modbus Signal thru the Ethernet, BR Jorge
pollo_rdz Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

4/25/2012 6:56 AM	Rate (0)
jklm Platinum Member Joined: 12/22/2006 Last visit: 1/25/2022 Posts: 1742 Rating: (309)	Hello, It is possible to run the third connection over the same CP, no new CP required. For the local port, I suggest to take a port above 2000, like 2002 (but it was may be a typing error in your request). You can only tell the exact meaning of the error code if you also look to the content of the parameter STAUTUS_FUNC that tells the name of the internal function that causes the problem. Let us assume that the it is the bloc AG_SEND that delivers an error code 8183, than it means: 8183 No configuration or the ISO/TCP service has not yet started on the Ethernet CP. In other words, it seems that the third connection is not loaded in the CP ... Or that the parameter ID of the Modbus block does not match with the ID in Netpro ... If you are sure the connection is loaded and the IDs are matching, try to take a trace with "wireshark" of the communication between both system. This will help you to see if the CP is sending a connection request, if it is accepted, if you really try to write soething, if the write is jected or not, ...
	Last edited by: jklm at: 4/25/2012 7:00 AM Best regards jklm Suggestion was helpful? Feel free to rate it.
Suggestion To thank Quote Answer

4/25/2012 9:50 AM	Rate (1)
Kaulquappe Posts: 3093 Rating: (323)	Hello Jorge, 8183 means, that the CP (passive connection partner) is waiting for the connection establishment from the active on. In the special diagnostic you can see a corresponding message, something like "passive connection establishment in progress, port 502". When the S7 acts a server you need a unspecified connection in NETPRO. You must not declare the remoteIP address and the port number. Regards, Kaulquappe
Kaulquappe Posts: 3093 Rating: (323)
Suggestion To thank Quote Answer

4/25/2012 6:38 PM	Rate (0)
pollo_rdz Posts: 8 Rating: (0)	jklm As you mentioned, I will need to select another Port for the connection and test again, here I include some of the screens I see in my System, How can I make sure the ID matches the Netpro number and in the Modbus Block, Kaulquappe would this error mean that I configured my port incorrectly? Attachment Modbus pictures.zip (666 Downloads)
pollo_rdz Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

4/25/2012 8:48 PM	Rate (0)
jklm Platinum Member Joined: 12/22/2006 Last visit: 1/25/2022 Posts: 1742 Rating: (309)	Hello, Your screenshot "Status2" indicates that the server is not responding or rejecting the connection("active connection establishment in progres"). As I suggested before, try to take a trace with wireshark.
	Best regards jklm Suggestion was helpful? Feel free to rate it.
Suggestion To thank Quote Answer

4/26/2012 8:48 AM	Rate (0)
Kaulquappe Posts: 3093 Rating: (323)	Hello Jorge, are you sure, that the S7 is client and Delta V is server? The client normally uses a port number starting from 2000 (not 202). Regards, Kaulquappe
Kaulquappe Posts: 3093 Rating: (323)
Suggestion To thank Quote Answer

4/26/2012 2:37 PM	Rate (0)
pollo_rdz Posts: 8 Rating: (0)	no, I will re assign a diffrent port number, maybe this will solve the connection issue, at the nonent I am not with my machine, so it will take ne some time to make these changes and test it again, when I do it, I will publish the results, Regards. Jorge
pollo_rdz Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

5/11/2012 11:22 AM	Rate (0)
pollo_rdz Posts: 8 Rating: (0)	Drear all here again, I made the changes in the connection without success, I double checked the configuration of the connection, to verify that is pointing to the Other station, and not to the TCP connection, I have no clue how to make the third connection worrk, any suggestions on how to troubleshoot and make it work, is welcome, BR Jorge Attachment 973 Modbus OB1 status8.JPG (598 Downloads)
pollo_rdz Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

5/11/2012 12:06 PM	Rate (0)
Sakura Silver Member Joined: 9/22/2010 Last visit: 7/25/2024 Posts: 225 Rating: (28)	Did you trace the network traffic with Wireshark? That usually helps in this kind of situation.

Suggestion To thank Quote Answer

5/11/2012 1:16 PM	Rate (0)
pollo_rdz Posts: 8 Rating: (0)	No I don't, I just used a modbus tester to try to make connection with the server, I will download the wireshark and test it, there are other devices connected to the DeltaV, and these are workin, but not this PLC, Any other idea will be welcome, BR
pollo_rdz Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

ModbusTCP

Follow us on