Hi Wizard,

If you send me your email to [snip] I can send you a download link from mediafire.

That is probably easier.

xmnj

Hi Wizard,

If you send me your email to [snip] I can send you a download link from mediafire.

That is probably easier.

Hello xmnj,

please Change email addresses only via PM.
Thanks. 

 Hello xmnj,

xmnj

Hi Wizard,

If you send me your email to [snip] I can send you a download link from mediafire.

That is probably easier.

 if you would send the download link to moderators we could try to upload even if it is bigger than standard size.

Best regards
CS Moderator

Hi again Wizard (and anyone else that might know the answer),

I coworker helped me find the place to edit the Alarm Texts (please see the attached screenshots) but now the next challenge is how to download this file to the PLC after I make my changes? 

Wizard

Hello xmnj,

Try to contact moderators.

Perhaps they have a solution.  to upload your project

Best regards,

Wizard

Hello Wizard,

Thank you for answering - I am grateful for your help and understand that you don't have to answer at all :-)

The CPU is CPU 315F-2 PN/DP (also see the attached screenshot).

I am using a standard network cable with RJ45 connectors to access the PLC (and flex panel) via a Siemens switch on the machine.

Wizard

Hello,

Good to hear you have found it.

(I'm sorry, but I didn't have time to look at your project)

What CPU are you using? Which programming cable are you using? 

Best regards,

Wizard

Hi again Wizard,

Each machine has a switch (or several) so all the IP addresses on the machine are within a group of numbers. That includes 3 IP addresses for PG.

The PLC and the flex panel are both in the same group and should be accessible via the same IP address on the PG.

I downloaded 2 modified block to the PLC when I was online with the machine a week ago. So I am pretty sure I can also connect to the flex panel.

Maybe I phrased my question wrong (and maybe I should call this thread solved and open a new thread but then a lot of info will be asked again) but what I need to know now (after I found the file with the texts) is how I operate the SW to download the text to the PLC or flex panel?

Wizard

Hello,

Please check the PG/PC interface.

Do you know the Password? (Because it is a Safety CPU).

Best regards,

Wizard

 Hello again Wizard,

Thank you for answering.

I knew how to download to Step 7 and I have already done so AS LONG AS we are talking about something in the Blocks folder (or the HW configuration).

Thank you for the manual I will see what I can find in that. But I have also already download safety logic several times.

BUT as we have previous concluded in this thread the Alarm texts in Danish language shown on the flex panel is coming from the PLC.

IF these texts have been included in the BLOCKS folder I would have a good guess how to download them BUT they are in a "Text Libraries" folder on the same level as Sources and Blocks.

So - how do I download (or in some other way implement the modified "Alarm_1_DK" file?

(Please also see the screenshots where I tell you that I found the file).

Wizard

Hello xmnj,

In WinCC flexible, you open your project.

Select in the tree, your HMI panel. Go to Project -> transfer -> transfer

Here you can select how to transfer project. (Ethernet) And then push the button Transfer

In Step 7, you have your project.

Select "Blocks", then go to PLC -> Download

Here is a link to manual:

SIMATIC Industrial Software S7 Distributed Safety - configuring and programming

See chapter 10.4

Best regards,

Wizard

Hello again Wizard,

Thank you for answering.

I have read the chapter but it doesn't quite solve my challenge.

 The original question have however (more or less) been answered so I will mark this thread solved and ask a new question regarding the download / transfer of the modified list.

Wizard

Hello,

Have a look at the following link:

SIMATIC Programming with STEP 7 V5.5

Perhaps chapter 16 might help you.

Best regards,

Wizard