SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

1PH6131-4NZ00-z Data

11/21/2011 9:10 PM	Rate (0)
machine_nut Posts: 10 Rating: (0)	Dir Sirs Could anyone tell me where to find the data sheet for this AC Spindle Motor? I have looked and can't seem to fin any thing on this motor. it is in a Hyunda 8S with 611d,controll Type Sinumrik 840-CT E. NCk software V04.09.05. Attached is a pic of the plate on the motor. What parameters would I use for this so I can check that I have no lost data. Thanks Gene Attachment 1PH6131_4NZ00_Z_motor.jpg (532 Downloads)
machine_nut Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

11/22/2011 11:46 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (882)	Hello, please check in DoconCD chapter 611 analog start up guide part 2 & 6.2. This may help you. Wish you all the best. DEEP.

Suggestion To thank Quote Answer

11/22/2011 2:14 PM	Rate (0)
denzilg_sa Bronze Member Joined: 7/5/2007 Last visit: 8/29/2025 Posts: 77 Rating: (5)	Hifindattached aparameter list for the spindle on the HIT8S Regards Denzilg Attachment hit8s - Spindle parameters.pdf (647 Downloads)

Suggestion To thank Quote Answer

11/22/2011 8:54 PM	Rate (0)
machine_nut Posts: 10 Rating: (0)	DEEPSTR2010 Hello, please check in DoconCD chapter 611 analog start up guide part 2 & 6.2. This may help you. Wish you all the best. DEEP. Thanks for your reply, I will check this out. Gene
machine_nut Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

11/22/2011 8:56 PM	Rate (0)
machine_nut Posts: 10 Rating: (0)	denzilg_sa Hifindattached aparameter list for the spindle on the HIT8S Regards Denzilg Thank you very much I think they will come in handy. Best Gene
machine_nut Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

12/5/2024 4:24 PM	Rate (0)
Elrouge Joined: 2/21/2024 Last visit: 2/25/2025 Posts: 3 Rating: (0)	denzilg_sa Hifindattached aparameter list for the spindle on the HIT8S Regards Denzilg How do I change the P15 . 1

Suggestion To thank Quote Answer

12/5/2024 10:00 PM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 9/3/2025 Posts: 4429 Rating: (398)	Do you know the small LED display with 3 buttons + P -, press P button, then using +/- to find P051, press P again set value =4(P051 is passowrd) then find P015.1 -it is drift compensation, You need make spindle enable, but zero speed set point (jump drive card 56/14 =0 V) use +/- to set valur until spindle stop drift , then go to P052, set it to 1, watch it change back to 0 , then shut of the power drift setting is done Elrouge denzilg_sa Hifindattached aparameter list for the spindle on the HIT8S Regards Denzilg How do I change the P15 . 1
	If you like my comments please use "Thank" bottom left or Rating Top right
Suggestion To thank Quote Answer

Share this page:

Share this page on...